Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 07259R

Form No. 3353-886 Rev A

Electric Bed Lift Kit

For Workman 1100/2100 and Twister Utility Vehicle

Model No. 07259, 0725 9R

Installation Instructions

Installation

Loose Parts

Use the c

hart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

None

Prepare the machine

Lift bracket, upper

Flange

head screws (5/16 x 3/4

inch)

Lift cy

linder support

Lift actuator

U-bolts

Flange nut (3/4 inch)

Carria

ge bolts (3/8 x 3/4 inch)

Clevis pin

Cotter pin

Nylon washer

Steel

washer

Install the bed lift

Switch

Fuse, 15 amp 1

Clevi

spin

Cotte

rpin

Install the switch

Note: If this kit is used on Model No. 07253

with a serial number of 210000243 and prior or

Model No. 07253TC with a serial number of

210000393 and prior, you will need to order an

Upper Lift Bracket, Part No. 99-7710-03.

Step

Preparing the Machine

Parts needed for this step:

None

Procedure

1. Position the machine on a level surface. Set

the parking brake, turn the ignition off, and

remove the key.

8111 Lyndale Avenue South

Bloomington, MN 55420

Original Instruct ions (EN)

Printed in the USA.

Summary of content (8 pages)

PAGE 1
Form No. 3353-886 Rev A Electric Bed Lift Kit For Workman 1100/2100 and Twister Utility Vehicle Model No. 07259, 07259R Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Step 1 2 3 Description Qty.
PAGE 2
Remove the 2 flange head screws securing each side of the latch rod bracket to the front of the rear frame (Figure 2). If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. 2 Remove the key from the ignition switch before you do any maintenance. 2. Raise the bed. Rotate the latch rod upward and raise the box with the other hand. 1 3. Raise the box to its full height; then lower it slightly to engage the prop rod (Figure 1).
PAGE 3
. Loosely mount the lift cylinder support to the right end of the rear axle with 2 U-bolts and 4 flange nuts (3/4 inch) while aligning the mounting holes with the holes in the battery tray (Figure 5).
PAGE 4
cotter pin. Position the components as shown in Figure 6. Step 3 6 5 Installing the Switch Parts needed for this step: 1 1 1 1 1 Switch Fuse, 15 amp Clevis pin Cotter pin Procedure 2 1. Remove the plug from the hole in the right side of the dash (Figure 7). G001323 Note: If the hole in the dash is in use, measure over 1/2 inch (13 mm) and cut another 0.835 inch x 1.46 inch (21 mm x 35 mm) rectangular hole in the dash.
PAGE 5
4. Plug the actuator harness into the vehicle harness connector, located near the fuse block. 5. Install the battery and connect the cables. 6. Press the switch upward to extend the actuator rod until it is aligned with the mounting holes in the upper lift bracket. Secure the rod to the bracket with the clevis pin and cotter pin. 7. Remove the screws and clip securing the prop rod to the frame rail (Figure 8). 3 1 2 G001325 Figure 8 1. 2. Prop rod Prop rod clip 3. Prop rod bracket 8.
PAGE 6
Operation Raising the Bed Driving the vehicle with the cargo box raised may cause the vehicle to tip or roll easier. The box structure may become damaged if the box is raised for an extended period of time while operating the vehicle. • Only operate the vehicle when the cargo box is down. • After a load has been dumped, lower the cargo box. 1. Turn the ignition key to the On position. 2. Push the top of the switch to raise the box.
PAGE 7
PAGE 8