Installation Instructions

ManualsBrandsToro ManualsAttachmentsElectric Bed Lift Kit, Workman e2050 Utility Vehicle

Form No. 3353-888 Rev A

Electric Bed Lift Kit

For For Workman e2050 Utility Vehicle

Model No. 07260

Installation Instructions

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

No parts required

–

Prepare the Machine

Lift bracket, upper

Flange head screw (5/16 x 3/4 inch)

Lift cylinder support

Lift actuator

U-bolts

Flange nut (3/8 inch)

Carriage bolts (3/8 x 3/4 inch)

Clevis pin

Cotter pin

Nylon washer

Steel washer

Install the bed lift

Solenoid

Bolt, #10 x 3/4 inch

Nut, #10 2

Accessory harness

Switch

Clevis pin, large

Cotter pin

Install the switch

Note: Deter mine the left and right sides of the

mac hine from the nor mal operating position.

Step

Preparing the Machine

No Parts Required

Procedure

1. P osition the mac hine on a lev el surface . Set

the parking brak e , tur n the ignition off , and

remo v e the k ey .

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Summary of content (8 pages)

PAGE 1
Form No. 3353-888 Rev A Electric Bed Lift Kit For For Workman e2050 Utility Vehicle Model No. 07260 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
4. Remove a short battery cable linking any two batteries in the battery bank to remove power from the system (Figure 2). If you leave the key in the ignition switch, someone could accidently start the machine and seriously injure you or other bystanders. Remove the key from the ignition switch before you do any maintenance. 2. Raise the bed. Rotate the latch rod upward and raise the box with the other hand. 3. Raise the box to its full height; then lower it slightly to engage the prop rod (Figure 1).
PAGE 3
Step 3. Loosely mount the lift cylinder support to the right end of the rear axle with 2 U-bolts and 4 ﬂange nuts (3/4 inch) while aligning the mounting holes with the holes in the battery tray (Figure 5). 2 Installing the Bed Lift Parts needed for this step: 1 4 1 1 2 6 2 1 1 1 3 Lift bracket, upper Flange head screw (5/16 x 3/4 inch) Lift cylinder support Lift actuator U-bolts Flange nut (3/8 inch) Carriage bolts (3/8 x 3/4 inch) Clevis pin Cotter pin Nylon washer Steel washer Procedure 1.
PAGE 4
cotter pin. Position the components as shown in Figure 6. 2. Install the solenoid on the existing plate using two bolts (#10 x 3/4 inch) and two nuts (#10) as shown in Figure 7. Figure 7 1. 2. 3. 4. Figure 6 1. Actuator 2. Lift cylinder support 3. Clevis pin 4. 5. 6. Cotter pin Nylon washer Steel washers 5. 6. 7. 8. Nut, #10 Accessory harness Large posts Small posts 3. Attach the accessory harness to the solenoid. Connect a large ring to each large post. Connect a small ring wire to each small post.
PAGE 5
cap. Connect the accessory harness to the 48v output connector as shown in Figure 8. 9. Plug the switch into the accessory connector in the dash. Insert the switch into the hole in the dash (Figure 9). Figure 8 1. Dash, under side 6. 2. Main harness 7. 3. Accessory harness 8. 4. 48v connector, from main 9. harness 5. 48v connector, from 10.
PAGE 6
Lowering the Bed The weight of the box may be heavy. Hands or other body parts could be crushed. Keep hands and other body parts clear when lowering the box. 1. Push the bottom of the switch to lower the box. Figure 10 1. Prop rod 2. Prop rod clip 3. Prop rod bracket Note: The bed will deform slightly before the actuator clutch begins to engage. If the bed ﬂoor deforms more than 1/4 inch add additional steel washers to the raise the lower stop of the actuator rod.
PAGE 7
PAGE 8