Installation Instructions

ManualsBrandsToro ManualsAttachmentsRoll-Over Protection System, Workman 1100/2100/e2000/MD/MDE/MDX/MDX-D Series and Twister Utility Vehicle

FormNo.3394-610RevA

Roll-OverProtectionSystem

Workman

1100/2100/e2000/MD/MDE/MDX/MDX-DSeriesand

Twister

UtilityVehicle

ModelNo.07276

ModelNo.07276R

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Disconnectthecontrolsontheseat

base.

Nopartsrequired

–

Removetheseatsandseatbases.

ROPSbar

Bolts(3/8inch)

Nuts(3/8inch)

MounttheseatbeltsandROPSbar.

Nut(3/8inch)

Seatbelt

Bolt(3/8inch)

SeatbeltROPSanchorbracket

Bolt(7/16inch)

Nut(7/16inch)

Seatbeltanchor,righthand

Seatbeltanchor,lefthand

Seatbeltlockassembly

Mounttheseatbeltstothemachine.

Nopartsrequired

–

Removethetransmissionspacer.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3394-610*A

Summary of content (8 pages)

PAGE 1
Form No. 3394-610 Rev A Roll-Over Protection System Workman® 1100/2100/e2000/MD/MDE/MDX/MDX-D Series and Twister® Utility Vehicle Model No. 07276 Model No. 07276R Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 © 2015—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Qty. Use No parts required – Disconnect the controls on the seat base.
PAGE 2
Disconnecting the Controls on the Seat Base for the 1110/2110/MD/MDE/MDX/MDX-D Models 1 Disconnecting the Controls on the Seat Base 1. Follow steps 1 through 4 above. 2. Remove the cotter pins and clevis pins securing the parking brake cables to the rear wheel brake levers (Figure 2). No Parts Required 4 Disconnecting the Controls on the Seat Base for the 1100/2100/MD/MDX/MDX-D and Twister Models 1. Remove the knob from the gear shift lever (Figure 1). 3 2 1 g026309 Figure 2 1. R-clamp 3.
PAGE 3
Disconnecting the Controls on the Seat Base for the 1100/2100/MD/MDE/MDX/MDX-D, e2060, and 2065 Models 2 1. Reach under the seat base and unplug the charger wire harness connector (Figure 3). Removing the Seats and Seat Bases 2. Remove the 2 bolts and washers securing the parking brake cover to the seat base (Figure 4). No Parts Required Procedure Remove the 8 bolts securing the seat base to the floor plate and front frame and lift the seats and seat base from the machine (Figure 5). Figure 4 1.
PAGE 4
3 4 Mounting the ROPS bar Mounting the Seat Belts to the Machine Parts needed for this procedure: Parts needed for this procedure: 1 ROPS bar 10 Bolts (3/8 inch) 8 Nut (3/8 inch) 10 Nuts (3/8 inch) 2 Seat belt 8 Bolt (3/8 inch) 2 Seat belt ROPS anchor bracket 4 Bolt (7/16 inch) 4 Nut (7/16 inch) 1 Seat belt anchor, right hand 1 Seat belt anchor, left hand 2 Seat belt lock assembly Procedure 1.
PAGE 5
1 2 g026313 Figure 10 1. 21 mm (2.1 cm) 6. Set the seat base into the mounting position on the machine. Figure 8 1. 54 mm (2 1/8 inch) 2. 51 mm (2 inch) 2. 32 mm (1 1/4 inch) 7. Insert the receiver end of each seat belt lock assembly into one of the newly drilled holes in the seat base (Figure 11). 4. Secure the left and right seat belt anchor to the front frame with 4 bolts (3/8 inch) and 4 nuts (3/8 inch) (Figure 9). Figure 11 8.
PAGE 6
5 Removing the Clutch Spacer (MD, dated 2013 or above, MDX serial numbers 310000001 and up, and MDX-D models only) No Parts Required Figure 13 MDX-D Models Procedure 1. Clutch Spacer It is possible to increase the ground speed when a ROPS is installed. 2. Remove the spring and discard the spacer (refer to Figure 12 and Figure 13) 1. Remove the bolts securing the primary clutch cover as shown in Figure 12 and Figure 13. 3. Install the spring and clutch cover.
PAGE 7
Notes: 7
PAGE 8