Installation Instructions

ManualsBrandsToro ManualsAttachments12V Power Plug Adapter Kit, Workman e2050/e2060/e2065 Utility Vehicle

Form No. 3357-675 Rev A

12V Power Plug Adapter Kit

For Workman e2050/e2060/e2065 Utility Vehicles

Model No. 07289 —Serial No. 270000001 and Up

Installation Instructions

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

No parts required

–

Prepare the machine.

Converter mount

Converter

Flange bolt (1/4 x 3/4 inch)

Lock nut (1/4 inch)

Assemble the converter.

Electric mount plate

Bolt (5/16 x 3/4 inch)

Lock nut (5/16 inch)

Fuse assembly

Install the fuse assembly and

electric mount plate.

Power plug assembly

Install the power plug assembly.

Bolt (5/16 x 3/4 inch)

Lock nut (5/16 inch)

Wiring harness

Wire ties

Mount the converter.

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Summary of content (8 pages)

PAGE 1
Form No. 3357-675 Rev A 12V Power Plug Adapter Kit For Workman e2050/e2060/e2065 Utility Vehicles Model No. 07289—Serial No. 270000001 and Up Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Step 1 Description Qty.
PAGE 2
Step Step 1 2 Preparing the Machine Assembling the Converter No Parts Required Parts needed for this step: 1 1 4 4 Procedure Batteries can give you a powerful electrical shock. Converter mount Converter Flange bolt (1/4 x 3/4 inch) Lock nut (1/4 inch) Procedure 1. Assemble the 12V converter to the converter mount plate (Figure 2). • Use tools with plastic handles or wrap the handles of metal tools with electrical tape.
PAGE 3
Step 3 Installing the Fuse Assembly and Electric Mount Plate Parts needed for this step: 1 1 1 1 Electric mount plate Bolt (5/16 x 3/4 inch) Lock nut (5/16 inch) Fuse assembly Figure 4 1. 2. 3. 4. Procedure 1. Remove the nut and bolt securing the horn to the steering column under the dash. Let the horn hang and replace the fasteners just removed. Frame Solenoid plate Electrical plate Bolt 5. 6. 7. 8. Flange nut Horn (harness not shown) Bolt (5/16 x 3/4 inch) Locknut (5/16 inch) 4.
PAGE 4
Step 4. Install the power plug interior and plastic cap through the dash in the hole previously drilled (Figure 8). 4 Installing the Power Plug Assembly Parts needed for this step: 1 Power plug assembly Procedure 1. On the dashboard, from the operator’s position, measure 2-7/8 inches to the right of the center of the key hole and 1-1/4 inch form the bottom edge of the switch cluster (Figure 6). Mark the dash at that point. Figure 8 1. Dash underside 2. Power plug interior 3.
PAGE 5
Step 5 Mounting the Converter and Installing Wiring Harness Parts needed for this step: 2 2 1 4 Bolt (5/16 x 3/4 inch) Lock nut (5/16 inch) Wiring harness Wire ties Procedure 1. Remove the Operator’s Manual tube from the dash. Remove the fasteners securing the R-clamps and tube to the dash (Figure 9). Retain all parts. Figure 9 1. Operator’s Manual tube 2. R-clamp 3. Bolt 2. For machines for with serial numbers 26999999999 and lower: For all others continue to step 3. A.
PAGE 6
Note: Orientate the ﬂat connector so that is facing the driver seat. 4. Locate the 12V power plug wire harness and locate the ﬂat connector at one end of the harness. 1 2 3 1. 4 2. 4. 3. 5 6 7 8 9 5 G005404 5. 6. 7. Figure 11 1. Bolt (3/8 x 1 inch) 2. 3. Lock nut (3/8 inch) 12V converter 4. Flat connector, 12V converter wiring 7. Operator’s Manual tube harness 5. 5 inches 8. R-clamp 6. Drill 3/8 inch diameter hole (vehicles with 9. Bolt heater kit) 5.
PAGE 7
. At the front of the machine, connect the plug marked power plug to the power plug in the dash (Figure 12). 5 2 3 4 1 Figure 12 1. Underside of the dash 2. Main wiring harness 3. Power plug assembly G005323 4. Plug, power plug 5. Plug, shown transparent for illustration purposes 8. Connect the plug marked fuse to the fuse installed in the solenoid plate. 9. Locate the OPTIONS +48 VDC plug on the main vehicle harness, remove the cap. 10.
PAGE 8