Installation Instructions

ManualsBrandsToro ManualsAttachmentsRight-Hand Light Kit, 2009 to 2011 Workman HD/HDX/HDX-D Series Utility Vehicle

FormNo.3361-406Rev B

LeftandRightHandLightKits

2009-2011 WorkmanHD/HDX/HDX-DSeriesUtilityVehicle

ModelNo.07315

ModelNo.07317

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Disconnectthenegativebatterycable

Nopartsrequired

–

Removethehood

Mainbeamlight2

Harnessadapter2

Installthemainbeamlights

Positionlight2Installthepositionlights

Flasher2

Clamp

Washerfacethreadformingscrew

Washer1

Installtheashers

Taillight2Installthetaillights

Panheadscrew,#6x2.5inches

Hexnut,#6

Locknut,#6

Signalmountbracket

Installthesignalcontroller

Switch

Decal1

Installtheswitch

Nopartsrequired

–

Installthehood

Nopartsrequired

–

Connectthenegativebatterycable

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3361-406 Rev B Left and Right Hand Light Kits 2009-2011 Workman HD/HDX/HDX-D Series Utility Vehicle Model No. 07315 Model No. 07317 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Use Qty.
PAGE 2
1 Disconnecting the Negative Battery Cable No Parts Required Procedure 1. Position the vehicle on a level surface, stop the engine, engage the parking brake and remove the key from the ignition. 2. Remove the battery cover. 3. Disconnect the negative battery cable from the battery. Figure 1 2 1. Removing the Hood Hood 3 No Parts Required Installing the Main Beam Lights Procedure 1.
PAGE 3
Figure 3 1. Figure 2 1. Old head lights 2. New Main beams 2. 1–3/8 to 1–1/2 inch diameter hole 3. Secure a position light to the hood at each location with (2) retainers (Figure 2). Position the lights with the amber lens to the outside. 3. Plug a harness adapter onto each main beam. 4 5 Installing the Position Lights Installing the Flashers Parts needed for this procedure: 2 1/4 inch diameter holes Parts needed for this procedure: Position light 2 Flasher Procedure 2 Clamp 1.
PAGE 4
Figure 5 1. Old Tail light 2. New Tail light 2. Unplug the wire harness connectors from the tail light connectors. Remove the lights. 3. Plug the wire harness connectors to the new tail light connectors. 4. Mount the tail lights to the fender brackets with the fasteners previously removed (Figure 5). Position the lights with the amber lens to the outside. Figure 4 1. Frame tube 4. 2. 3. Clamp Washer 5. Washer face thread forming screw Flasher 7 2.
PAGE 5
Figure 6 1. 2. Signal controller Nuts 3. 4. Old screws New screws Figure 8 1. 2. Under the steering wheel, remove the two screws securing the console to the steering pump (Figure 7). Wire harness 6. Locate the vehicle wire harness labeled signal controller and plug it into the signal controller harness. 8 Installing the Switch Parts needed for this procedure: Figure 7 1. 2. Signal controller Signal mount bracket 3. Locknuts 4. Console screws (2) 1 Switch 1 Decal Procedure 3.
PAGE 6
10 Connecting the Negative Battery Cable No Parts Required Figure 10 1. Decal 2. Procedure Switch 1. Connect the negative battery cable to the battery. 3. Affix the decal to the dash panel, next to the switch (Figure 10). 2. Install the battery cover. 4. Locate the wire harness, with the loop back connector, under the dash (Figure 11). The harness will be labeled light switch. Figure 11 1. Switch 2. Wire harness connector 5. Unplug the loop back connector from the harness connector. 6.
PAGE 7
Notes: 7
PAGE 8