Installation Instructions

ManualsBrandsToro ManualsAttachments12V Power Plug Adapter Kit, Workman MDE Utility Vehicle

FormNo.3363-440RevA

12VPowerPlugAdapterKit

Workman

MDEUtilityVehicle

ModelNo.07318—SerialNo.310000001andUp

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Convertermount

Converter

Flangebolt(1/4x3/4inch)

Locknut(1/4inch)

Assembletheconverter.

Fuseassembly1

Installthefuseassemblyandelectric

mountplate.

Powerplugassembly1Installthepowerplugassembly.

Bolt(5/16x3/4inch)

Locknut(5/16inch)

Wiringharness1

Wireties4

Mounttheconverter.

PreparingtheMachine

NoPartsRequired

Procedure

CAUTION

Batteriescangiveyouapowerfulelectricalshock.

•Usetoolswithplastichandlesorwrapthe

handlesofmetaltoolswithelectricaltape.

•Becarefulnottocontactbothapositiveterminal

andanegativeterminalatthesametime.

1.Positionthevehicleonalevelsurface,engagethe

parkingbrakeandrotatetheOn/OffkeytotheOff

position.

2.Raisethebedtoaccessthevehiclebatteries.Remove

oneofthebatterycableslinkinganytwobatteries

inthebanktoremovepowerfromthesystem

(Figure1).

Figure1

1.Batterylinkcable

3.Openthefronthoodtogainaccesstofrontendof

themachine.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3363-440 Rev A 12V Power Plug Adapter Kit Workman® MDE Utility Vehicle Model No. 07318—Serial No. 310000001 and Up Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 No parts required – Prepare the machine. 2 Converter mount Converter Flange bolt (1/4 x 3/4 inch) Lock nut (1/4 inch) 1 1 4 4 Assemble the converter. Fuse assembly 1 Install the fuse assembly and electric mount plate.
PAGE 2
3 Assembling the Converter Installing the Fuse Assembly and Electric Mount Plate Parts needed for this procedure: Parts needed for this procedure: 1 Converter mount 1 Converter 4 Flange bolt (1/4 x 3/4 inch) 4 Lock nut (1/4 inch) 1 Fuse assembly Procedure Install the fuse assembly to the open hole between the two existing fuses under the dash (Figure 3). Procedure 1. Assemble the 12V converter to the converter mount plate (Figure 2). 4 1 1 2 3 3 2 G005314 G012348 Figure 2 1.
PAGE 3
4 Installing the Power Plug Assembly Parts needed for this procedure: 1 Power plug assembly Procedure Figure 6 1. Dash underside 2. Power plug interior 1. On the dashboard, from the operator’s position, measure 2-7/8 inches to the right of the center of the key hole and 1-1/4 inch from the bottom edge of the switch cluster (Figure 4). Mark the dash at that point. 5.
PAGE 4
5 Mounting the Converter and Installing Wiring Harness Parts needed for this procedure: 2 Bolt (5/16 x 3/4 inch) 2 Lock nut (5/16 inch) 1 Wiring harness 4 Wire ties Procedure 1. Remove the Operator’s Manual tube from the dash. Loosen the fasteners securing the R-clamps and tube to the dash (Figure 7). Rotate the clamps upward and install the manual tube. G012350 Figure 7 2. Install the 12V converter assembly as shown in Figure 8 to the outside of the pedal box assembly.
PAGE 5
3 4 2 1 G005323 Figure 9 4. Plug, power plug 5. Plug, shown transparent for illustration purposes 1. Underside of the dash 2. Main wiring harness 3. Power plug assembly 6. Connect the two single red wires to the fuse installed in the solenoid plate. 7. Locate the OPTIONS +48 VDC plug on the main vehicle harness, remove the cap. 8. Connect the plug marked +48 VOLTS IN on the 12V converter harness to the plug marked OPTIONS +48 VDC on main vehicle harness. 9.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8