3362-141 Rev B ROPS CERTIFIED DELUXE HARD CAB Model 07328 Operators Manual Installation Instructions This cab is intended to be used on the following TORO product: WORKMAN ® MD, MDX, and MDE This cab is manufactured for TORO by Jodale Perry Corporation
3362-141 Rev B Table of contents 1. Safety instructions……………………………………………3 2. Inspection guide……………………………………………..5 3. Safety labels and location…………………………………...6 4. Operating features……………………………………………7 5. Vehicle preparation…………………………………………..8 6. Mounting instructions….……………………………………..9 7. Parts list………………………………………………..…….15 8. Parts photos…………………………………………………16 9. Optional equipment…………………………………………16 10. To the purchaser…………………………………………….17 11.
362-141 Rev B SAFETY INSTRUCTIONS BEFORE OPERATING • Read and understand the contents of this material before operating the vehicle. Become thoroughly familiar with the controls, capabilities and proper use of equipment. • • This cab fits all Workman® MD Series with serial numbers with 28xxxxxxx or higher in gas and electric. DO NOT weld, cut, drill, or modify cab structure in any matter. • DO NOT allow children to operate vehicle. Do not allow adults to operate with out proper training.
3362-141 Rev B SAFETY INSTRUCTIONS While operating • Verify capacity rating for the vehicle. Make sure that the GVW capacities are not exceeded. • Avoid sudden stops or sharp turns. • Always use safety belts. • Never allow riders on top of cab or in bed while operating vehicle. • Stay alert for hidden hazards and traffic. • Avoid sudden starts and excessive speeds. • Use extreme care when working around fences, ditches or on hillsides. • Check clearances carefully before driving under any objects.
3362-141 Rev B ROPS Certified Cab, Roll Over Protection Structure Inspection Guide Cab has been certified to ISO 21299 ROPS certified cab like any other safety devices needs to be periodically inspected to verify that the integrity of the device has not been compromised though normal machine use, misuse, age degrading, modifications, or rollovers.
3362-141 Rev B Replace decals immediately if damaged or missing.
3362-141 Rev B OPERATING FEATURES Dome light on/off switch Windshield wiper on/off switch Fuse access cover Front windshield vent sliders 7
3362-141 Rev B VEHICLE PREPARATION Step 1. Position the machine on a level surface. Set the parking brake, turn the ignition off, and remove the key. If you are installing cab onto a Workman MDE, a 12V Power Plug Adapter Kit, model number 07289 is needed to power cab. Step 2. Remove knob from the gear shift lever. (Figure 1.) (For Workman MDE skip to step 4) Step 3. Remove 4 screws that secure shifter plate to shifter bracket. (Figure 1.) Step 4. Remove 4 screws securing the shifter plate to seat base.
3362-141 Rev B VEHICLE PREPARATION STEP 8. Mount the left and right seat belt brackets to the frame as shown in Figure 4. with 3/8 X .75 hex flange head bolts and flange locking nuts. STEP 9. Using the dimensions shown in figure 5, locate, mark and drill (2)1.00 Diameter holes in the top of seat base. Locate one hole on each side of the centre compartment. Note; Locating depression marks may already be in the seat base. Step 10. Set seat back into mounting position on vehicle Step 11.
3362-141 Rev B INSTALLATION INSTRUCTIONS Step 1. Remove side and front composite panels. Retain panels and fasteners for later reinstall.
3362-141 Rev B INSTALLATION INSTRUCTIONS Step 2 Install lift brackets to upper door cross tube using 3/8 X 2.5 bolt and nut into .375 diameter hole provided as shown. Step 3 Lower cab onto vehicle using lift brackets. Note: leaving seat base loose is recommended. Slightly tilting the front of the cab down will aide installation. Some interference will occur with hip restraints on the seat and the cab, but the cab will flex over these.
3362-141 Rev B INSTALLATION INSTRUCTIONS Step 4 install (8) 3/8 x 1.00 long hex flange bolts and flange nuts loosely. 4 per side as indicated in illustration. Step 5 Install rear support brackets by slipping them between the cab and the Workman frame. Then install (3) 3/8 x 1.00 hex flange bolts and flange nuts on both sides. Then tighten all (14) bolts, 7 per side to 33 +/- 5 ft. lbs. Remove lift brackets and install (2) plastic hole plugs.
3362-141 Rev B INSTALLATION INSTRUCTIONS Step 6 Assemble retractable seat belt as shown to tabs welded to cab frame with 7/16 X 1.00 hex bolts and nuts. Step 7 Reassemble all composite panels that were previously removed with hardware previously used. Step 8 (For Workman MD, MDX only) loosen bolt located on left side of dash and install wire harness in R-clamp with harness attached in it, back to dash using hardware.
3362-141 Rev B INSTALLATION INSTRUCTIONS Step 9 Before operation of the unit, the front springs need to be replaced with the heavy duty springs provided. Raise front of vehicle off the ground and securely place on jack stands. Remove shock assemblies. Use a spring compressor tool to remove old springs and install new springs. Re-install shock assemblies. Turn shock adjuster three clicks up from the longest position. Refer to service manual for further instructions on spring replacement.
3362-141 Rev B STANDARD PARTS LIST QTY Description 2 Seat belt brackets (See parts photo) 1 R-Clamp 2 Rear Bracket (See parts photo) 14 Bolt, Flange, 3/8” x 1” YD 18 Nut, Flange, 3/8”, YD 2 Lift brackets 2 3/8” plugs 2 Seat Belt sets 4 Bolt 7/16”-14 UNC x 1”,YD 4 Nut, whiz 7/16” 2 Bolt, 3/8” x 3” 2 Nut, 3/8” 1 Fuel hose, ¼” Id x 21” 2 Lifting Brackets (See parts photo) 1 Fitting, - 1/8” npt – ¼” hose barb 90 degree 2 Spring, Heavy Duty ELECTRICAL CONNECTOR LIST QTY Descri
3362-141 Rev B PARTS PHOTOS Rear brackets Seat belt brackets, LH & RH Lifting brackets Optional equipment for Workman® MD Series Cab Option Part No. Sliding door kit 07352 Solid door kit 07353 Cooling fan - Available thru Jodale Perry Rotating beacon - Available thru Jodale Perry Jodale Perry Corporation 204-822-9100 www.jodaleperry.
3362-141 Rev B TO THE PURCHASER All products are designed to give safe, dependable service if they are operated and maintained according to instructions. Read and understand this manual before installation or operation. This manual has been prepared to assist the owner and operators in the safe installation, and suitable maintenance of this cab. The information is applicable to products at the time of manufacture and does not include modifications made afterwards.
3362-141 Rev B 18
