Form No. 3371-290 Rev A 1/3 Area Platform Lift Workman® Heavy-Duty Utility Vehicle Model No. 07347—Serial No. 311000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
Contents Introduction Introduction................................................................. 2 Safety ........................................................................... 3 Before Operating ................................................. 3 While Operating................................................... 3 Maintenance......................................................... 3 Safety and Instructional Decals ............................. 4 Setup .............................................
Safety • When raising platform be alert for overhead obstructions which could cause eye, head or crushing injuries. Before Operating • Stand clear of scissor arms while platform is moving. • Read and understand the contents of this manual before operating the platform lift. Become familiar with all controls and know how to stop quickly. A replacement manual is available at www.Toro.com. • Make sure area is clear of bystanders before lowering platform.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost.
93-3703 93-3705 93-3707 93-3706 93-3709 5
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description 1 2 3 4 5 6 7 8 9 10 11 Use Qty. No parts required – Remove the seat, shroud and fender assemblies No parts required – Remove the hood Main Wire Harness w/ Relays Cable Tie Screw, 1/4 x 3/4 inch Nut, 1/4 inch Fuse Parking brake switch Screws Rear level switch bracket Rear level switch w/ harness 1 7 2 2 1 1 2 1 1 No parts required – Reinstall hood Reinforcing Plate Flange HD.
CAUTION 1 Pressurized hot coolant escaping can cause serious burns. Remove the Seat, Shroud and Fender Assemblies Allow engine to cool enough to touch before removing overflow tube or radiator cap. 6. Remove the capscrews securing the seats and shroud to mounting brackets (Figure 3). Remove the seats and shroud. No Parts Required Procedure 1. Position vehicle on a clean, level surface, stop engine, engage parking brake and remove key from ignition switch. Disconnect positive cable from battery. 2.
2. While grasping the hood in the headlight openings, lift up on the hood to release the lower mounting tabs from the bumper slots. 3. Pivot the bottom of the hood upward until the top mounting tabs can be pulled from the dash slots. 4. Pivot the top of the hood forward and unplug the wire connectors from the head lights. 5. Remove the hood. 3 Figure 4 Install the Main Wire Harness w/Relays 1.
mounting holes, mount the level switch bracket to rear axle with the locknuts previously removed. 4 Mount the Parking Brake Switch Parts needed for this procedure: 1 Parking brake switch 2 Screws Procedure 1. Mount the parking brake switch to the parking brake mount with two screws as shown in Figure 5. G016822 Figure 6 1. Hitch plate 2. Level switch bracket 2. Route switch harness forward, along differential lock cable to left side of machine.
Figure 8 G016821 1. Hitch frame extension tube Figure 7 1. Hitch plate 2. Locate and remove the threaded insert from the mounting hole in left and right vehicle frame channels, as shown in Figure 9. 2. Level switch bracket 2. Route switch harness forward, along shift cable to left side of machine. Harness must not interfere with any hot (exhaust) or moving parts. Secure harness to shift cable with cable ties. 6 Reinstall Hood No Parts Required Figure 9 Procedure 1. Vehicle frame channel 1.
5. Connect ground wire from lift to engine ground. 6. Remove the nut from the positive battery clamp (Figure 11). 7. Insert the positive wire from the lift and the ring terminal end of the red wire from the front harness onto the cable clamp screw and loosely secure it with the nut removed (Figure 11). 2 3 1 Figure 10 1. Lift 2. Reinforcing plate g017228 4. Mount each side of lift to frame channels with a reinforcing plate and (2) 3/8-16 x 1 inch large flange head capscrews and flange nuts (Figure 10).
10 Mount Circular Bubble Level Parts needed for this procedure: 1 Circular Bubble Level Procedure Figure 13 Affix circular level to top of console cover positioning as shown in Figure 12. 1. No—Step decal For Workman HDX and HDX-D vehicles 1. Affix operation decal to top of console cover positioning as shown in Figure 12. 2. Affix the "No Step" decals to top of radiator, as shown in Figure 14. G01681 1 Figure 12 1. Circular level 2. Operation decal 11 1 G01021 1 Install Decals Figure 14 1.
Emergency Lowering Valve Knob Product Overview Push the blue knob inward, rotate it 90 degrees counterclockwise, and pull it out to activate the emergency lowering valve (Figure 16). To stop the lift and return it to normal operation, push the blue knob inward, rotate it 90 degrees clockwise and pull it out. Controls Up Button Press "UP" button to raise lift (Figure 15). Down Button Press "DOWN" button to lower lift (Figure 15). Key Switch Rotate key switch to authorize use of lift.
Operation Check Tire Pressure Check Oil Level Check tire pressure every 8 hours or daily to assure proper levels. The lift reservoir is filled at the factory with 5W30 oil. Check level before lift is first operated and every 8 hours or daily, thereafter. Capacity of system is 1.5 qt. Refer to the vehicle operator's manual for proper tire inflation specification. 1. Position the vehicle on a level surface. Engaging Safety Locks 2. Raise lift and engage the safety locks.
Operating the Lift 2 The 1/3 platform lift is designed to be used only with a Workman Vehicle and must be mounted with the wiring harness, level, decals, switches and all interlock switches installed. 1 DANGER Improper operation of platform lift may cause serious personal injury or death. To reduce risk to operator and bystanders: • Read and understand all safety instructions in Workman and Platform Lift Operator's Manuals and warning labels.
If lift does not operate: • Make sure vehicle key and lift key are in "ON" position. 1 • Make sure vehicle is parked on less than a 5 degree angle slope. • Make sure vehicle parking brake is "On". • Make sure vehicle engine is “OFF” and the oil pressure light is “ON” 6. When finished with work operation, lower lift all the way down to stops and remove key from lift pendant control to prevent operation when unattended.
Operating Tips DANGER Contact with moving scissor arms can cause personal injury. The electrical system, battery and hydraulic lift cylinder are not designed for continuous use. Allow some time, approximately 1-1/2 to 2 minutes, between lift operations to maintain operating temperatures. • Stand clear of scissor arms while platform is moving. Frequent use without the engine running or idling, between lift use, may discharge the battery.
DANGER Falling objects and overhead obstructions can cause personal injury. • Always wear hard hat and eye protection while operating platform or while in area below platform. • Never drop or throw articles from raised platform. • When raising platform be alert for overhead obstructions which could cause eye, head or crushing injuries.
Maintenance Battery Care 1. Battery electrolyte level must be properly maintained and the top of the battery kept clean. If the machine is stored in a location where temperatures are extremely high, the battery will run down more rapidly than if the machine is stored in a location where temperatures are cool.
WARNING CALIFORNIA Proposition 65 Warning Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. WARNING Charging the battery produces gasses that can explode. Never smoke near the battery and keep sparks and flames away from battery. WARNING Battery terminals or metal tools could short against metal components causing sparks.
Schematics Electrical Schematic (Rev.
Notes: 22
Notes: 23
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro® Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
