Installation Instructions

ManualsBrandsToro ManualsAttachmentsElectric Bed Lift Kit, 2011 to 2013 Workman MD/MDX Utility Vehicle

FormNo.3366-590RevA

ElectricBedLiftKit

2011andAfterWorkman

MD/MDXUtilityVehicle

ModelNo.07381—SerialNo.311000001andUp

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

PreparetheMachine

Liftbracket,upper

Pan-head,Phillipsscrew(3/8x2-1/2

inches)

Flangelocknut(Whizlock)(3/8inch)

Liftactuator

Clevispin

Cotterpin

Installthebedlift.

Switch

Thermalfuse,15amp

Clevispin(3-1/2inch)

Cotterpin

Installtheswitch

Note:Determinetheleftandrightsidesofthemachine

fromthenormaloperatingposition.

PreparingtheMachine

NoPartsRequired

Procedure

1.Positionthemachineonalevelsurface.Setthe

parkingbrake,turntheignitionoff,andremovethe

key.

WARNING

Ifyouleavethekeyintheignitionswitch,

someonecouldaccidentlystartthemachineand

seriouslyinjureyouorotherbystanders.

Removethekeyfromtheignitionswitchbefore

youdoanymaintenance.

2.Lifttheleveroneithersideoftheboxandliftthe

boxup(Figure1).

g014860

Figure1

1.Lever3.Detentslot

2.Proprod

3.Pulltheproprodintothedetentslot,securingthe

box(Figure1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3366-590 Rev A Electric Bed Lift Kit 2011 and After Workman® MD/MDX Utility Vehicle Model No. 07381—Serial No. 311000001 and Up Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
WARNING 2 A raised box could fall and injure persons that are working beneath it. • Always use the prop rod to hold the box up before working under the box. Installing the Bed Lift • Remove any load material from the box before raising it. Parts needed for this procedure: 4. Remove the 4 flange nuts securing the latch rod brackets to the underside of the box (Figure 2). Remove and save the rod and latches. Leave the carriage bolts in the holes and secure them to the bed with the flange nuts.
PAGE 3
clevis pin (2-1/4 inch) and cotter pin to the secure the lift cylinder to the arm as shown in Figure 4. G009003 2 1 3 5 4 Figure 5 1. Plugged hole 2. Switch 3. Cut new hole (if required). Figure 4 1. Actuator 2. Lift cylinder support 2. Plug the switch into the harness connector in the dash. Insert the switch into the hole in the dash (Figure 5). 3. Clevis pin 4. Cotter pin 3. Install a new thermal fuse (15 amp) into the open slot in the fuse block. 3 4.
PAGE 4
Operation Important: When a ratcheting noise is heard, the box lift is completely extended or retracted. Do not continue pressing the switch. Raising the Bed WARNING Driving the vehicle with the cargo box raised may cause the vehicle to tip or roll easier. The box structure may become damaged if the box is raised for an extended period of time while operating the vehicle. • Only operate the vehicle when the cargo box is down. • After a load has been dumped, lower the cargo box. 1.