Installation Instructions

ManualsBrandsToro ManualsAttachmentsElectric Bed Lift Kit, 2011 to 2013 Workman MDE Utility Vehicle

FormNo.3366-602RevA

ElectricBedLiftKit

for2011andAfterWorkman

MDEUtilityVehicle

ModelNo.07382—SerialNo.311000001andUp

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

PreparetheMachine

Liftbracket,upper

Pan-head,Phillipsscrew(3/8x2-1/2

inches)

Flangelocknut(Whizlock)(3/8inch)

Liftcylindersupport

Liftactuator

U-bolts2

Flangelocknut(Nylock)(3/8inch)

Carriagebolts(3/8x3/4inch)

Clevispin

Cotterpin

Installthebedlift

Solenoid

Bolt(#10x3/4inch)

Nut(#10)

Accessoryharness1

Switch

Clevispin,large

Cotterpin

Installtheswitch

Note:Determinetheleftandrightsidesofthemachine

fromthenormaloperatingposition.

PreparingtheMachine

NoPartsRequired

Procedure

1.Positionthemachineonalevelsurface.Setthe

parkingbrake,turntheignitionoff,andremovethe

key.

WARNING

Ifyouleavethekeyintheignitionswitch,

someonecouldaccidentlystartthemachineand

seriouslyinjureyouorotherbystanders.

Removethekeyfromtheignitionswitchbefore

youdoanymaintenance.

2.Lifttheleveroneithersideoftheboxandliftthe

boxup(Figure1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3366-602 Rev A Electric Bed Lift Kit for 2011 and After Workman® MDE Utility Vehicle Model No. 07382—Serial No. 311000001 and Up Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
1 2 3 1 g014860 2 Figure 1 1. Lever 2. Prop rod 3. Detent slot 3 g015185 Figure 3 1. Carriage bolts—leave in the bed 2. Latch rod 3. Pull the prop rod into the detent slot, securing the box (Figure 1). WARNING 3. Flange nut 2 A raised box could fall and injure persons that are working beneath it. • Always use the prop rod to hold the box up before working under the box. • Remove any load material from the box before raising it. Installing the Bed Lift Parts needed for this procedure: 4.
PAGE 3
nuts (3/8 inch). Tighten the 4 flange nuts on the U-bolts equally to make sure the bracket is aligned to the axle. Tighten the two nuts securing the rear of the bracket to the rear frame (Figure 5). 6. Mount the bottom end of the lift actuator to the lift cylinder support with a clevis pin and cotter pin. Position the components as shown in Figure 6. Figure 4 1. Bosses 2. Upper lift bracket 2.
PAGE 4
5. Locate the box lift kit connector on the main harness and remove the cap. Attach accessory harness to box lift kit connector wire from main harness. 6. Cap 48v output connector on accessory harness. 7. Place the switch connector into position behind the plug in the dash as shown in Figure 8. 8. Remove the plug from the hole in the right side of the dash (Figure 9). 9. Plug the switch into the accessory connector in the dash. Insert the switch into the hole in the dash (Figure 9). Figure 7 1. 2. 3. 4.
PAGE 5
upper lift bracket. Secure the rod to the bracket with the large clevis pin and cotter pin. 14. Remove the nuts and bracket securing the prop rod to the underside of the bed. Install the nuts back on the carriage bolts to secure them in the bed and cover the holes. 15. Slide the prop rod forward to remove it from the bracket on the frame. Retain the prop rod components for future use. Note: If the electric box lift is ever removed, install the prop rod using the existing fasteners and the prop rod bracket.
PAGE 6
Operation Important: When a ratcheting noise is heard, the box lift is completely extended or retracted. Do not continue pressing the switch. Raising the Bed WARNING Driving the vehicle with the cargo box raised may cause the vehicle to tip or roll easier. The box structure may become damaged if the box is raised for an extended period of time while operating the vehicle. • Only operate the vehicle when the cargo box is down. • After a load has been dumped, lower the cargo box. 1.
PAGE 7
Notes: 7
PAGE 8