Form No. 3444-525 Rev B Workman® HDX Utility Vehicle Model No. 07383—Serial No. 409100000 and Up Model No. 07384—Serial No. 409100000 and Up Model No. 07386—Serial No. 409100000 and Up Register at www.Toro.com.
Important: With your mobile device, you can scan the QR code on the serial number decal (if equipped) to access warranty, parts, and other product information.
Contents Electrical System Maintenance ........................... 43 Electrical System Safety ................................... 43 Servicing the Fuses .......................................... 43 Jump-Starting the Machine............................... 44 Servicing the Battery......................................... 45 Drive System Maintenance .................................. 45 Checking the Front Differential-Oil Level .............................................................
Safety This machine has been designed in accordance with the requirements of SAE J2258 (Nov 2016). General Safety This product is capable of causing personal injury. Always follow all safety instructions to avoid serious personal injury. • Read and understand the contents of this Operator’s Manual before you start the machine. Ensure that everyone using this product knows how to use it and understands the warnings. • Use your full attention while operating the machine.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decalbatterysymbols Battery Symbols Some or all of these symbols are on your battery. 1. Explosion hazard 6. Keep bystanders away from the battery. 2. No fire, open flame, or smoking 7. Wear eye protection; explosive gases can cause blindness and other injuries. 3. Caustic liquid/chemical burn hazard 4.
decal105-4215 105-4215 decal106-2355 1. Warning—avoid pinch points. 106-2355 1. Slow 3. Transmission—third high; no fast speed 2. Fast decal106-2353 106-2353 1. Electrical power point decal106-2377 106-2377 1. Locked 8. Warning—read the Operator's Manual. 2. Differential lock 9. Entanglement hazard, shaft—keep bystanders out of the operating area. 3. Unlocked 10. Retract hydraulics 4. Hydraulic lock 11. Extend hydraulics 5. Engage 12. Transmission—high speed 6. Power takeoff (PTO) 13.
decal110-0806 110-0806 decal106-6755 1. Caution—do not use starting fluid 106-6755 1. Engine coolant under pressure. 3. Warning—do not touch the hot surface. 2. Explosion hazard—read the Operator's Manual. 4. Warning—read the Operator's Manual. decal115-2047 115-2047 1. Warning—do not touch the hot surface. decal106-7767 106-7767 1. Warning—read the Operator's Manual; avoid tipping the machine; wear the seat belt; lean away from the direction the machine is tipping.
decal115-2282 115-2282 1. Warning—read the Operator's Manual. 2. Warning—stay away from moving parts; keep all guards and shields in place. 3. Crushing hazard—keep bystanders out of the operating area; do not carry passengers in the cargo bed; keep arms and legs inside of the vehicle at all times; use seat belts and handholds. decal115-7741 115-7741 1. Read the Operator’s Manual before servicing transmission fluid. decal115-7756 115-7756 decal115-7723 1. High-flow hydraulics—engaged 115-7723 1.
decal121-6287 121-6287 decal121-6286 121-6286 1. Check the coolant level daily before use of the machine. Read the Operator's Manual before checking the engine-coolant level. 1. Fill the reservoir with engine coolant to the bottom of the filler neck. 2. Do not open or add coolant to the radiator; doing so introduces air into the system and results in engine damage. Add only engine coolant to the reservoir. decal121-9776 121-9776 1.
decal137-9896 137-9896 1. 4x4 engage button decal139-3341 139-3341 1. Tank 2. Warning—the hydraulic-fluid pressure is 138 bar (2,000 psi). 3. Pressure decal140-4604 140-4604 1. Headlights 4. Engine—run 2. Horn 5. Engine—start 3.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 Description Use Qty. Roll bar Flange-head bolt (1/2 x 1-1/4 inches) 1 6 Install the roll bar. No parts required – Check the fluid levels and tire pressure. No parts required – Burnish the brakes. Note: Determine the left and right sides of the machine from the normal operating position.
2 Checking the Fluid Levels and Tire Pressure No Parts Required Procedure 1. Check the engine-oil level before and after you first start the engine; refer to Checking the Engine-Oil Level (page 40). 2. Check the transaxle/hydraulic-fluid level before you first start the engine; refer to Checking the Transaxle/Hydraulic-Fluid Level (page 56). 3. Check the brake-fluid level before you first start the engine; refer to Checking the Brake-Fluid Level (page 52). 4.
Product Overview Controls Become familiar with all the controls before you start the engine and operate the machine. Control Panel g347585 Figure 4 1. Light switch 5. Power point 2. High-flow hydraulics switch (TC models only) 6. Key switch 3. Horn button 7. Supervisor switch 4. Display 8.
Display g347586 Figure 5 1. Fuel gauge 6. Check-engine indicator 2. Tachometer/engine speed (rpm) 7. Tachometer-speedometer location change button/Speedometer conversion button 3. Speedometer (km/h or mph) 8. Hour meter 4. Coolant-temperature gauge and light 9. Oil-pressure-warning light 5. Glow-plug indicator (diesel machines only) 10.
Accelerator Pedal Gear-Shift Lever Use the accelerator pedal (Figure 6) to vary the ground speed of the machine when the transmission is in gear. Pressing down the accelerator pedal increases the engine speed and ground speed. Releasing the pedal decreases the engine speed and ground speed. Fully press the clutch pedal and move the shift lever (Figure 7) into the desired gear selection. A diagram of the shift pattern is shown below.
Hydraulic-Lift Lock The hydraulic-lift lock secures the lift lever, so that the hydraulic cylinders do not operate when the machine is not equipped with a bed (Figure 8). It also locks the lift lever in the ON position when using the hydraulics for attachments. High-Low Range Shifter The high-low range shifter adds 3 additional speeds for precise speed control (Figure 8): • You must stop the machine completely before shifting between the HIGH and LOW range. g350294 Figure 8 1. Parking-brake lever 5.
Supervisor Switch Charge Indicator Move the supervisor switch (Figure 4) to the SLOW position and remove the key. The supervisor switch limits the engine speed to 2,200 rpm when the machine is in third gear in the HIGH range, which limits the top speed to 21 km/h (13 mph). The charge indicator illuminates when the battery discharges. If the light illuminates during operation, stop the machine, shut off the engine, and check for possible causes, such as the alternator belt (Figure 5).
Tachometer Passenger Handhold The tachometer displays the speed of the engine (Figure 5). The passenger handhold is located on the dashboard (Figure 9). Note: 3,300 rpm is the desired engine speed for 540 rpm PTO operation. Check-Engine Light The check-engine light illuminates to indicate an engine malfunction; refer to Responding to a Check-Engine Light (page 41). Speedometer The speedometer registers the ground speed of the machine (Figure 5).
Specifications Note: Specifications and design are subject to change without notice.
Performing Daily Maintenance Operation Note: Determine the left and right sides of the machine from the normal operating position. Service Interval: Before each use or daily Before Operation Before starting the machine each day, perform the Each Use/Daily procedures listed in Maintenance (page 30).
Adding Fuel • For best results, use only clean, fresh (less than 30 days old), unleaded gasoline with an cetane rating of 87 or higher ((R+M)/2 rating method). • Ethanol: Gasoline with up to 10% ethanol (gasohol) or 15% MTBE (methyl tertiary butyl ether) by volume is acceptable. Ethanol and MTBE are not the same. Gasoline with 15% ethanol (E15) by volume is not approved for use.
Checking the Safety-Interlock System During Operation During Operation Safety Service Interval: Before each use or daily The purpose of the safety-interlock system is to prevent the engine from cranking or starting, unless you press the clutch pedal. General Safety • The owner/operator can prevent and is responsible CAUTION • If the safety-interlock switches are disconnected or damaged, the machine could operate unexpectedly, causing personal injury. • Do not tamper with the safety-interlock switches.
• • • • • • • • • • • • • Always wear your seat belt; ensure that it is hidden objects. Uneven terrain could overturn the machine. Tall grass can hide obstacles. Use care when approaching blind corners, shrubs, trees, or other objects that may obscure your vision. Do not drive the machine near drop-offs, ditches, or embankments. The machine could suddenly roll over if a wheel goes over the edge or if the edge gives way.
the cargo bed and/or towing a trailer; refer to Specifications (page 19). • Distribute the load in the cargo bed evenly to improve the stability and control of the machine. • Before dumping, ensure that there is no one behind the machine. • Do not dump a loaded cargo bed while the machine is sideways on a slope. The change in weight distribution may cause the machine to overturn. Operating the Cargo Bed g024612 Figure 14 Raising the Cargo Bed 1.
Engaging the 4-Wheel Drive 4-Wheel Drive Models Only To enable automatic 4-Wheel Drive, press the top of the rocker switch into the 4X4 AUTO position (Figure 16). g227244 Figure 16 1. 4x4 auto enable—on When the 4WD switch is on, the machine automatically engages the 4-wheel drive if the sensor detects the back wheels spinning freely. When the 4-wheel drive is engaged, the 4WD switch light turns on. g026141 Figure 15 1. Latch handle 2. 4x4 auto enable—off 3.
Note: Avoid long periods of engine idling. CAUTION Use the chart below to determine the ground speed of the machine at 3,600 rpm. Gear Range Ratio Speed (kmh) Speed (mph) 1 L 82.83 : 1 4.7 2.9 2 L 54.52 : 1 7.2 4.5 3 L 31.56 : 1 12.5 7.7 1 H 32.31 : 1 12.2 7.6 2 H 21.27 : 1 18.5 11.5 3 H 12.31 : 1 31.9 19.8 R L 86.94 : 1 4.5 2.8 R H 33.91 : 1 11.6 7.
Using the Hydraulic Bed-Lift Lever to Control Hydraulic Attachments This position is similar to the LOWER (QUICK COUPLER B POSITION). It also directs hydraulic fluid to quick coupler B, except that the lever is held in this position by a detent lever in the control panel. This allows hydraulic fluid to flow continuously to equipment that use a hydraulic motor. • OFF Position This is the normal position for the control valve when it is not in use.
Troubleshooting the Hydraulic Control After Operation • Difficulty in connecting or disconnecting quick couplers. After Operation Safety The pressure is not relieved (the quick coupler is under pressure). General Safety • Before you leave the operating position, do the • The power steering is turning with great difficulty or it is not turning at all. following: – The hydraulic-fluid level is low. – Park the machine on a level surface. – The hydraulic-fluid temperature is too hot.
Hauling the Machine Towing the Machine • Use care when loading or unloading the machine In case of an emergency, you can tow the machine for a short distance; however, this is not the standard operating procedure. into a trailer or a truck. • Use full-width ramps for loading the machine into a trailer or a truck. WARNING • Tie the machine down securely. Towing at excessive speeds could cause a loss of steering control, resulting in personal injury.
Maintenance Maintenance Safety • Keep all parts of the machine in good working condition and all the hardware properly tightened. Replace all worn or damaged decals. • Do not allow untrained personnel to service the • • • • • • • • • • • • • • machine. Before you leave the operating position, do the following: – Park the machine on a level surface. – Shift the transmission to the NEUTRAL position. – Engage the parking brake. – Lower the cargo bed. – Shut off the machine and remove the key.
Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 2 hours • Torque the front and rear wheel lug nuts. After the first 10 hours • • • • • After the first 50 hours • Change the engine oil and filter. • Adjust the engine-valve clearance. After the first 100 hours • Perform the guidelines for breaking in a new machine. Before each use or daily • Inspect the seat belt(s) for wear, cuts, and other damage.
Maintenance Service Interval Every 800 hours Maintenance Procedure • • • • Change the front differential oil (4-wheel drive models only). Change the hydraulic fluid and clean the strainer. Replace the hydraulic filter. If you are not using the recommended hydraulic fluid or have ever filled the reservoir with an alternative fluid, replace the high-flow hydraulic fluid and filter. Every 1,000 hours • Flush/replace the coolant system fluid. • Change the brake fluid.
Maintaining the Machine under Special Operating Conditions Important: If the machine is subjected to any of the conditions listed below, perform maintenance twice as frequently: • Desert operation • Cold climate operation—below 10°C (50°F) • Trailer towing • Frequent operation in dusty conditions • Construction work • After extended operation in mud, sand, water, or similar dirty conditions, do the following: – Have your brakes inspected and cleaned as soon as possible.
Removing the Full Bed 1. Start the engine, engage the hydraulic-lift lever, and lower the bed until the cylinders are loose in the slots. 2. Release the lift lever and shut off the engine. 3. Remove the lynch pins from the outer ends of the cylinder rod clevis pins (Figure 22). g009164 Figure 21 1. Bed support 3. Bed 2. Cylinder barrel 4. Remove the bed support from the cylinder, and insert it into the brackets on the back of the ROPS panel.
Installing the Full Bed Note: If you are installing the bed sides on the flat bed, it is easier to install them before installing the bed on the machine. Ensure that the rear pivot plates are bolted to the bed frame/channel so that the lower end angles to the rear (Figure 23). g002370 Figure 24 1. Wear block 3. Carriage bolt 2. Spacer bracket 1. Ensure that the lift cylinders are fully retracted. 2.
Raising the Machine DANGER A machine on a jack may be unstable and slip off the jack, injuring anyone beneath it. • Do not start the machine while the machine is on a jack, as the engine vibration or wheel movement could cause the machine to slip off the jack. • Always remove the key from the key switch before getting off the machine. g009824 • Block the tires when the machine is on a jack. Figure 26 1.
3. Pivot the top of the hood forward and unplug the wire connectors from the headlights (Figure 27). 4. Remove the hood. Lubrication Greasing the Bearings and Bushings Installing the Hood 1. Connect the lights. 2. Insert the top mounting tabs into the frame slots (Figure 27). 3. Insert the lower mounting tabs into the frame slots (Figure 27). 4. Ensure that the hood is fully engaged in the top, sides, and bottom grooves.
g024682 Figure 30 g010571 Figure 29 • U-joint (18); refer to Figure 31 • 4-wheel drive shaft (3); refer to Figure 31 • Clutch (1); refer to Figure 30 • Brake (1); refer to Figure 30 g010359 Figure 31 38
Engine Maintenance 4. Engine Safety Note: Holes in the filter appear as bright spots. Inspect the element for tears, an oily film, or damage to the rubber seal. If the filter is damaged, do not use it. • Shut off the engine, remove the key, and wait for all moving parts to stop before checking the oil or adding oil to the crankcase. Note: To prevent engine damage, always operate the engine with the air filter and cover installed.
Servicing the Engine Oil Note: Change the oil more frequently when operating conditions are extremely dusty or sandy. Note: Dispose of the used engine oil and oil filter at a certified recycling center. Engine-Oil Specifications Oil Type: Detergent engine oil (API SJ or higher) Crankcase Capacity: 3.2 L (3.4 US qt) when the filter is changed g028637 Viscosity: See the table below. Figure 34 1. Filler cap 2. Dipstick g016095 Figure 33 5.
5. Apply a light coat of clean oil to the new filter seal before screwing it on. 6. Screw the filter on until the gasket contacts the mounting plate. Then tighten the filter 1/2 to 2/3 of a turn. Note: Do not overtighten. 7. Add the specified oil to the crankcase. Responding to a Check-Engine Light Note: Engine-fault code information can be accessed by your Toro commercial products service staff only. g002373 Figure 35 1. Note the clearance between the fill device and the oil-fill neck. 8.
Replacing the Spark Plugs Fuel System Maintenance Service Interval: Every 100 hours/Yearly (whichever comes first) Replace the spark plugs if necessary. Type: NGK-R BKR5E (or equivalent) Replacing the Fuel Filter Air Gap: 0.81 mm (0.032 inch) Service Interval: Every 400 hours Important: A cracked, fouled, dirty, or malfunctioning spark plug must be replaced.
Inspecting Fuel Lines and Connections Electrical System Maintenance Service Interval: Every 400 hours/Yearly (whichever comes first) Electrical System Safety Inspect the fuel lines, fittings, and clamps for signs of leaking, deterioration, damage, or loose connections. • Disconnect the battery before repairing the machine. Disconnect the negative terminal first and the positive last. Connect the positive terminal first and the negative last.
decal115-7813 Figure 40 1. Power outlet (10 A) 5. Lights/brake (15 A) 2. Switched power (10 A) 6. Hazard lights (10 A) 3. Fuel pump/supervisor switch (10 A) 7. 4WD/transmission (10 A) g010326 Figure 41 1. Battery cover 4. Horn/power point (15 A) 2. Connect a jumper cable between the positive posts of the 2 batteries (Figure 42). Note: The positive post may be identified by a + sign on top of the battery cover. Jump-Starting the Machine 3.
4. Drive System Maintenance Start the engine in the machine providing the jump-start. Note: Let it run for a few minutes, then start your engine. 5. Remove the negative jumper cable first from your engine, then the battery in the other machine. 6. Install the battery cover to the battery base. Checking the Front Differential-Oil Level 4-Wheel Drive Models Only Service Interval: Every 100 hours/Monthly (whichever comes first)—Check the level of the front differential oil (4-wheel drive models only).
Changing the Front Differential Oil Inspecting the Constant-Velocity Boot 4-Wheel Drive Models Only 4-Wheel Drive Models Only Service Interval: Every 800 hours (4-wheel drive models only). Service Interval: Every 200 hours (4-wheel drive models only). Differential oil specification: Mobil 424 hydraulic fluid Inspect the constant-velocity boot for cracks, holes, or a loose clamp. Contact your Authorized Service Dealer for repair if you find any damage. 1. Park the machine on a level surface. 2.
Adjusting the High-Low Cable Inspecting the Tires Service Interval: Every 200 hours Front tires air pressure specification: 220 kPa (32 psi) 1. 2. 3. Service Interval: Every 100 hours Remove the clevis pin securing the high-low cable to the transaxle (Figure 44). Rear tires air pressure specification: 124 kPa (18 psi) Loosen the clevis jam nut and adjust the clevis so that the clevis hole aligns with the hole in the transaxle bracket.
Checking the Front Wheel Alignment Service Interval: Every 400 hours/Yearly (whichever comes first) 1. Ensure that the tire pressures are correct before checking the front wheel alignment; refer to Checking the Tire Pressure (page 20). 2. Either have an operator in the operator’s seat or add weight to the driver’s seat equal to the average operator of the vehicle. The operator or weight must remain on the seat for the duration of the front wheel alignment procedure. 3. g010329 Figure 49 1.
Torquing the Wheel Lug Nuts Cooling System Maintenance Service Interval: After the first 2 hours After the first 10 hours Cooling System Safety Every 200 hours • Swallowing engine coolant can cause poisoning; Wheel lug nut torque specification: 109 to 122 N∙m (80 to 90 ft-lb) keep out of reach from children and pets. Discharge of hot, pressurized coolant or touching a hot radiator and surrounding parts can cause severe burns.
Removing Debris from the Cooling System Note: The coolant should be up to the bottom of the filler neck when the engine is cold. Service Interval: Before each use or daily—Remove debris from the engine area and radiator. (Clean it more frequently in dirty conditions.) 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key. 4. Clean the engine area thoroughly of all debris. 5.
Changing the Engine Coolant Service Interval: Every 1,000 hours/Every 2 years (whichever comes first) Cooling-system capacity: 3.7 L (4 US qt) Coolant type: a 50/50 solution of water and permanent ethylene-glycol antifreeze 1. Park the machine on a level surface. 2. Raise the bed and install the bed safety support on the extended lift cylinder to secure the bed. CAUTION If the engine has been running, the cooling system pressurizes with hot coolant that can escape and cause burns.
Brake Maintenance Checking the Brake-Fluid Level Service Interval: Before each use or daily—Check the brake-fluid level. Check the brake-fluid level before you first start the engine. Every 1,000 hours/Every 2 years (whichever comes first)—Change the brake fluid. g002379 Figure 57 Brake-fluid type: DOT 3 1. Brake-fluid reservoir 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key. 4.
Adjusting the Brake Pedal Service Interval: Every 200 hours Note: Remove the font hood to ease the adjustment procedure. 1. g033488 Figure 59 1. Knob Remove the cotter pin and clevis pin securing the master cylinder yoke to the brake-pedal pivot (Figure 60). 3. Parking-brake lever 2. Set screw 3. Rotate the knob (Figure 59) until a force of 20 to 22 kg (45 to 50 lb) is required to actuate the lever. 4. Tighten the set screw when finished (Figure 59).
Belt Maintenance Adjusting the Alternator Belt Service Interval: After the first 10 hours—Check the condition and tension of the alternator belt. Every 200 hours—Check the condition and tension of the alternator belt. g036549 Figure 61 1. Clutch pedal 1. Raise the bed and position the safety support on the extended lift cylinder to secure the bed. 2. Check the tension by pressing the belt at mid span between the crankshaft and alternator pulleys with 10 kg (22 lb) of force (Figure 62). 3.
Controls System Maintenance Adjusting the Clutch Pedal Service Interval: Every 200 hours Note: You can adjust the clutch-pedal cable at the bell housing or at the clutch-pedal pivot. You can remove the front hood to easily access to the pedal pivot. 1. g009276 Figure 64 Loosen the jam nuts securing the clutch cable to the bracket on the bell housing (Figure 63). 1. Clutch pedal Note: You may remove and rotate the ball joint, if additional adjustment is required. 2. 9.2 to 9.
Adjusting the Accelerator Pedal 1. 2. Hydraulic System Maintenance Park the machine on a level surface, engage the parking brake, shut off the engine, and remove the key. Hydraulic System Safety • Seek immediate medical attention if fluid is injected Adjust the ball joint on the accelerator cable (Figure 66) to allow 2.54 to 6.35 mm (0.100 to 0.250 inch) of clearance between the accelerator pedal arm and the top of the diamond tread floor plate (Figure 67), when you apply 11.
g009623 Figure 69 1. Hydraulic reservoir 2. Drain plug g002376 Figure 68 1. Dipstick 5. Unscrew the dipstick from the top of the transaxle and wipe it with a clean rag. 6. Screw the dipstick into the transaxle and ensure that it is fully seated. 7. Unscrew the dipstick and check the fluid level. 5. Note the orientation of the hydraulic hose and 90° fitting connected to the strainer on the side of the reservoir (Figure 70). 6. Remove the hydraulic hose and 90° fitting. 7.
13. Check the hydraulic-fluid level and replenish it, if required. Important: Use only the hydraulic fluid specified. Other fluids could damage the system. Replacing the Hydraulic Filter Service Interval: After the first 10 hours—Replace the hydraulic filter. Every 800 hours—Replace the hydraulic filter. Important: Use of any other filter may void the warranty on some components. 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key. 4.
Checking the High-Flow Hydraulic-Fluid Level Servicing the High-Flow Hydraulic System TC Models Only TC Models Only Service Interval: Before each use or daily—Check the high-flow hydraulic-fluid level (TC models only). (Check the level of hydraulic fluid before the engine is first started, and daily thereafter) Hydraulic Fluid Specifications The reservoir is filled at the factory with high-quality hydraulic fluid.
Changing the High-Flow Hydraulic Fluid and Filter Raising the Cargo Bed in an Emergency TC Models Only The cargo bed can be raised in an emergency without starting the engine by cranking starter or by jumping the hydraulic system. Service Interval: Every 1,000 hours—If you are using the recommended hydraulic fluid, replace the high-flow hydraulic filter. Raising the Cargo Bed using the Starter Every 2,000 hours—If you are using the recommended hydraulic fluid, change the high-flow hydraulic fluid.
g019543 Figure 75 1. Jumper hoses 7. Keep all bystanders away from the machines. 8. Start the second machine and move the lift lever to the raise position, which raises the disabled cargo bed. 9. Move the hydraulic-lift lever to the NEUTRAL position, and engage the lift-lever lock. g009822 Figure 73 1. Quick-coupler hose A 2. Quick-coupler hose B 10. 3. On the disabled machine, connect the 2 jumper hoses to the hoses that were disconnected (Figure 74). 4. Cap the unused fittings.
Cleaning Washing the Machine Wash the machine as needed using water alone or with a mild detergent. You may use a rag when washing the machine. Important: Do not use brackish or reclaimed water to clean the machine. Important: Do not use power-washing equipment to wash the machine. Power-washing equipment may damage the electrical system, loosen important decals, or wash away necessary grease at friction points. Avoid excessive use of water near the control panel, engine, and battery.
Storage damaged at temperatures below 0°C (32°F). A fully charged battery maintains its charge for about 50 days at temperatures lower than 4°C (40°F). If the temperatures will be above 4°C (40°F), check the water level in the battery and charge it every 30 days. Storage Safety • Shut off the machine, remove the key, and wait for all movement to stop before you leave the operator’s position. Allow the machine to cool before adjusting, servicing, cleaning, or storing it. 13.
Troubleshooting Problem Possible Cause Corrective Action The engine does not start, starts hard, or fails to keep running. 1. The hydraulic lever is locked in forward position 1. Move the hydraulic lever out of forward position. 2. 3. 4. 5. 2. 3. 4. 5. The fuel tank is empty. The fuel-shutoff valve is closed. The oil level in the crankcase is low. The throttle is not in the correct position. 6. There is dirt, water, or stale fuel is in the fuel system. 7. The air cleaner is dirty. 8.
Notes:
Notes:
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
The Toro Warranty Two-Year or 1,500 Hours Limited Warranty Parts Conditions and Products Covered The Toro Company warrants your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for 2 years or 1,500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).