Form No. 3427-775 Rev A Workman® HDX-D Utility Vehicle Model No. Model No. Model No. Model No. Register at www.Toro.com. Original Instructions (EN) 07385—Serial No. 404350001 and Up 07385TC—Serial No. 404350001 and Up 07387—Serial No. 404350001 and Up 07387TC—Serial No.
numbers on the product. Write the numbers in the space provided. This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet. Important: With your mobile device, you can scan the QR code on the serial number decal (if equipped) to access warranty, parts, and other product information.
Contents Inspecting Fuel Lines and Connections............. 43 Electrical System Maintenance ........................... 44 Electrical System Safety ................................... 44 Servicing the Fuses .......................................... 44 Jump-Starting the Machine............................... 44 Servicing the Battery......................................... 45 Drive System Maintenance .................................. 46 Checking the Front Differential-Oil Level ..........................
Safety This machine has been designed in accordance with the requirements of SAE J2258 (Nov 2016). General Safety This product is capable of causing personal injury. Always follow all safety instructions to avoid serious personal injury. • Read and understand the contents of this Operator’s Manual before you start the machine. Ensure that everyone using this product knows how to use it and understands the warnings. • Use your full attention while operating the machine.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decalbatterysymbols Battery Symbols Some or all of these symbols are on your battery. 1. Explosion hazard 6. Keep bystanders away from the battery. 2. No fire, open flame, or smoking 7. Wear eye protection; explosive gases can cause blindness and other injuries. 3. Caustic liquid/chemical burn hazard 4.
decal105-4215 105-4215 decal106-2355 1. Warning—avoid pinch points. 106-2355 1. Slow 3. Transmission—third high; no fast speed 2. Fast decal106-2353 106-2353 1. Electrical power point decal106-2377 106-2377 1. Locked 8. Warning—read the Operator's Manual. 2. Differential lock 9. Entanglement hazard, shaft—keep bystanders out of the operating area. 3. Unlocked 10. Retract hydraulics 4. Hydraulic lock 11. Extend hydraulics 5. Engage 12. Transmission—high speed 6. Power takeoff (PTO) 13.
decal106-6755 106-6755 1. Engine coolant under pressure. 3. Warning—do not touch the hot surface. 2. Explosion hazard—read the Operator's Manual. 4. Warning—read the Operator's Manual. decal106-7767 106-7767 1. Warning—read the Operator's Manual; avoid tipping the machine; wear the seat belt; lean away from the direction the machine is tipping. decal115-2047 115-2047 1. Warning—do not touch the hot surface.
decal115-2282 115-2282 1. Warning—read the Operator's Manual. 2. Warning—stay away from moving parts; keep all guards and shields in place. 3. Crushing hazard—keep bystanders out of the operating area; do not carry passengers in the cargo bed; keep arms and legs inside of the vehicle at all times; use seat belts and handholds. decal115-7741 115-7741 1. Read the Operator’s Manual before servicing transmission fluid. decal115-7756 115-7756 decal115-7723 1. High-flow hydraulics—engaged 115-7723 1.
decal115-7814 115-7814 decal121-6286 121-6286 1. Check the coolant level daily before use of the machine. Read the Operator's Manual before checking the engine-coolant level. 2. Do not open or add coolant to the radiator; doing so introduces air into the system and results in engine damage. Add only engine coolant to the reservoir. decal121-6287 121-6287 1. Fill the reservoir with engine coolant to the bottom of the filler neck.
decal121-9776 121-9776 1. Warning—read the Operator’s Manual and receive proper training before operating the machine. 4. Warning—engage the parking brake, shut off the engine, and remove the key from the key switch before walking away from the machine. 5. Tipping hazard—take turns slowly; drive slowly up and across cliffs; with no load, do not exceed 32 kph (20 mph); while carrying a load or when driving on uneven terrain, drive slowly. 2. Warning—wear hearing protection. 3.
decal138-3523 138-3523 1. Headlights 4. Engine—Run 2. Horn 5. Engine—Start 3. Engine—Shut off decal139-3341 139-3341 1. Tank 2. Warning—the hydraulic-fluid pressure is 138 bar (2,000 psi). 3.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Use Qty. Steering wheel 1 Install the steering wheel (TC models only). Roll bar Flange-head bolt (1/2 x 1-1/4 inches) 1 6 Install the roll bar. No parts required – Check the fluid levels and tire pressure. No parts required – Burnish the brakes. Note: Determine the left and right side of the machine from the normal operating position. 5.
2 3 Installing the Roll Bar Checking the Fluid Levels and Tire Pressure Parts needed for this procedure: 1 Roll bar 6 Flange-head bolt (1/2 x 1-1/4 inches) No Parts Required Procedure Procedure 1. 2. 1. Apply medium-grade (service-removable) thread-locking compound to the threads of the 6 flange-head bolts (1/2 x 1-1/4 inches). Check the engine-oil level before and after you first start the engine; refer to Checking the Engine-Oil Level (page 41). 2.
Product Overview Controls Become familiar with all the controls before you start the engine and operate the machine. Note: Determine the left and right sides of the machine from the normal operating position. Control Panel g036549 Figure 6 1. Clutch pedal 3. Accelerator pedal 2. Brake pedal Clutch Pedal You must fully press the clutch pedal (Figure 6) to disengage the clutch when starting the engine or shifting transmission gears.
Gear-Shift Lever Fully press the clutch pedal and move the shift lever (Figure 7) into the desired gear selection. A diagram of the shift pattern is shown below. g009160 Figure 7 g240581 Figure 8 Important: Do not shift the transaxle to the 1. Parking-brake lever 5. High-low range shifter REVERSE or FORWARD gear unless the machine is motionless; otherwise, you could damage the transaxle. 2. Hydraulic-bed lift 6. 4-wheel drive button (4-wheel drive models only) 3. Hydraulic-lift lock 7.
Hydraulic-Lift Lock Hour Meter The hydraulic-lift lock secures the lift lever, so that the hydraulic cylinders do not operate when the machine is not equipped with a bed (Figure 8). It also locks the lift lever in the ON position when using the hydraulics for attachments. The hour meter indicates the total hours of machine operation. The hour meter (Figure 5) starts to function whenever you rotate the key switch to the ON position or if the engine is running.
Coolant-Temperature Gauge and Light Horn Button The coolant-temperature gauge and light registers the coolant temperature in the engine and operates only when the key switch is in ON position (Figure 5). The indicator light blinks red if the engine overheats. Pressing the horn button activates the horn (Figure 5). Press the horn button to sound the horn. TC Models Only Charge Indicator The charge indicator illuminates when the battery discharges.
Tachometer Passenger Handhold The tachometer displays the speed of the engine (Figure 5 and Figure 9). The passenger handhold is located on the dashboard (Figure 10). Note: The white triangle indicates the desired engine speed for 540 rpm PTO operation. g009815 g010514 Figure 10 Figure 9 1. Engine speed (rpm) 1. Passenger handhold 2. 3,300 rpm for 540 rpm PTO operation 2.
Specifications Note: Specifications and design are subject to change without notice.
Checking the Tire Pressure Operation Service Interval: Before each use or daily Before Operation Front tires air pressure specification: 220 kPa (32 psi) Before Operation Safety Tear tires air pressure specification: 124 kPa (18 psi) General Safety Important: Check the tire pressure frequently to ensure proper inflation. If the tires are not inflated to the correct pressure, the tires will wear prematurely and may cause the 4-wheel drive to bind.
Adding Fuel Use only clean, fresh diesel fuel or biodiesel fuels with low (<500 ppm) or ultra-low (<15 ppm) sulfur content. The minimum cetane rating should be 40. Purchase fuel in quantities that can be used within 180 days to ensure fuel freshness. • Use summer grade diesel fuel (No. 2-D) at temperatures above -7°C (20°F) and winter grade (No. 1-D or No. 1-D/2-D blend) below that temperature.
Checking the Safety-Interlock System During Operation Service Interval: Before each use or daily During Operation Safety The purpose of the safety-interlock system is to prevent the engine from cranking or starting, unless you press the clutch pedal. General Safety • The owner/operator can prevent and is responsible for accidents that may cause personal injury or property damage.
Rollover Protection System (ROPS) Safety • Operate the machine only in good visibility. Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain could overturn the machine. Tall grass can hide obstacles. Use care when approaching blind corners, shrubs, trees, or other objects that may obscure your vision. • The ROPS is an integral safety device. • Do not remove the ROPS from the machine.
on level ground. If you must stop the machine, avoid sudden speed changes, which can cause the machine to tip or roll over. Do not engage the brakes suddenly when rolling rearward, as this may cause the machine to overturn. CAUTION If a load is concentrated near the back of the cargo bed when you release the latches, the bed may unexpectedly tip open, injuring you or bystanders. Loading and Dumping Safety • Center loads in the cargo bed, if possible.
result. If engine fails to start after 10 seconds, turn the key to the OFF position. Check the controls and starting procedure, wait 10 additional seconds, and repeat the starting operation. Engaging the 4-Wheel Drive 4-Wheel Drive Models Only To enable automatic 4-Wheel Drive, press the top of the rocker switch into the 4X4 AUTO position (Figure 17). g026141 g227244 Figure 16 1. Latch handle Figure 17 3. Latch pin 1. 4x4 auto enable—on 2. 4x4 auto enable—off 2.
Driving the Machine Using the Differential Lock 1. Disengage the parking brake. 2. Fully press the clutch pedal. 3. Move the gear-shift lever to first gear. 4. Release the clutch pedal smoothly while pressing the accelerator pedal. 5. When the machine gains enough speed, remove your foot from the accelerator pedal, fully press the clutch pedal, move the gear-shift lever to the next gear, and release the clutch pedal while pressing the accelerator pedal. 6.
Using the Hydraulic Bed-Lift Lever to Control Hydraulic Attachments Using the Hydraulic Control The hydraulic control supplies hydraulic power from the machine pump whenever the engine runs. You can use the power through the quick couplers at the rear of the machine. • OFF Position This is the normal position for the control valve when it is not in use. In this position, the work ports of the control valve are blocked and any load is held by the check valves in both directions.
Troubleshooting the Hydraulic Control This position is similar to the LOWER (QUICK COUPLER B POSITION). It also directs hydraulic fluid to quick coupler B, except that the lever is held in this position by a detent lever in the control panel. This allows hydraulic fluid to flow continuously to equipment that use a hydraulic motor. • Difficulty in connecting or disconnecting quick couplers. The pressure is not relieved (the quick coupler is under pressure).
After Operation After Operation Safety General Safety • Before you leave the operating position, do the following: – Park the machine on a level surface. g009820 – Shift the transmission to the NEUTRAL position. Figure 19 – Engage the parking brake. 1. Eye hole in the frame (each side) – Lower the cargo bed. – Shut off the machine and remove the key (if equipped). – Wait for all movement to stop • Allow the machine to cool before adjusting, servicing, cleaning, or storing it.
Towing a Trailer The machine is capable of pulling trailers and attachments of greater weight than the machine itself. Several types of tow hitches are available for the machine, depending on your application. Contact your Authorized Service Dealer for details. When equipped with a tow hitch bolted onto the rear axle tube, your machine can tow trailers or attachments with a maximum gross trailer weight (GTW) up to 1587 kg (3,500 lb).
Maintenance Maintenance Safety • Keep all parts of the machine in good working condition and all the hardware properly tightened. Replace all worn or damaged decals. • Do not allow untrained personnel to service the • • • • • • • • • • • • • • machine. Before you leave the operating position, do the following: – Park the machine on a level surface. – Shift the transmission to the NEUTRAL position. – Engage the parking brake. – Lower the cargo bed.
Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 2 hours • Torque the front and rear wheel lug nuts. After the first 10 hours • • • • • After the first 50 hours • Change the engine oil and filter. • Adjust the engine-valve clearance. After the first 100 hours • Perform the guidelines for breaking in a new machine. Before each use or daily • Inspect the seat belt(s) for wear, cuts, and other damage.
Maintenance Service Interval Every 800 hours Maintenance Procedure • • • • Change the front differential oil (4-wheel drive models only). Change the hydraulic fluid and clean the strainer. Replace the hydraulic filter. If you are not using the recommended hydraulic fluid or have ever filled the reservoir with an alternative fluid, replace the high-flow hydraulic fluid and filter. Every 1,000 hours • Flush/replace the coolant system fluid. • Change the brake fluid.
Maintaining the Machine under Special Operating Conditions Important: If the machine is subjected to any of the conditions listed below, perform maintenance twice as frequently: • Desert operation • Cold climate operation—below 10°C (50°F) • Trailer towing • Frequent operation in dusty conditions • Construction work • After extended operation in mud, sand, water, or similar dirty conditions, do the following: – Have your brakes inspected and cleaned as soon as possible.
Removing the Full Bed 1. Start the engine, engage the hydraulic-lift lever, and lower the bed until the cylinders are loose in the slots. 2. Release the lift lever and shut off the engine. 3. Remove the lynch pins from the outer ends of the cylinder rod clevis pins (Figure 23). g009164 Figure 22 1. Bed support 3. Bed 2. Cylinder barrel 4. Remove the bed support from the cylinder, and insert it into the brackets on the back of the ROPS panel.
Installing the Full Bed Note: If you are installing the bed sides on the flat bed, it is easier to install them before installing the bed on the machine. Ensure that the rear pivot plates are bolted to the bed frame/channel so that the lower end angles to the rear (Figure 24). g002370 Figure 25 1. Wear block 3. Carriage bolt 2. Spacer bracket 1. Ensure that the lift cylinders are fully retracted. 2.
Raising the Machine DANGER A machine on a jack may be unstable and slip off the jack, injuring anyone beneath it. • Do not start the machine while the machine is on a jack, as the engine vibration or wheel movement could cause the machine to slip off the jack. • Always remove the key from the key switch before getting off the machine. g009824 • Block the tires when the machine is on a jack. Figure 27 1.
3. Pivot the top of the hood forward and unplug the wire connectors from the headlights (Figure 28). 4. Remove the hood. Lubrication Greasing the Bearings and Bushings Installing the Hood 1. Connect the lights. 2. Insert the top mounting tabs into the frame slots (Figure 28). 3. Insert the lower mounting tabs into the frame slots (Figure 28). 4. Ensure that the hood is fully engaged in the top, sides, and bottom grooves.
• Brake (1); refer to Figure 31 g002394 g010571 Figure 31 Figure 30 • U-joint (18); refer to Figure 32 • Clutch (1); refer to Figure 31 • Accelerator (1); refer to Figure 31 • 4-wheel drive shaft (3); refer to Figure 32 g010359 Figure 32 39
Engine Maintenance 4. Engine Safety Note: Holes in the filter appear as bright spots. Inspect the element for tears, an oily film, or damage to the rubber seal. If the filter is damaged, do not use it. • Shut off the engine, remove the key, and wait for all moving parts to stop before checking the oil or adding oil to the crankcase. Note: To prevent engine damage, always operate the engine with the air filter and cover installed.
Servicing the Engine Oil Note: Change the oil more frequently when operating conditions are extremely dusty or sandy. Note: Dispose of the used engine oil and oil filter at a certified recycling center. Engine-Oil Specifications Oil Type: Detergent engine oil (API SJ or higher) Crankcase Capacity: 3.2 L (3.4 US qt) when the filter is changed g028637 Viscosity: See the table below. Figure 35 1. Filler cap 2. Dipstick g016095 Figure 34 5.
5. Apply a light coat of clean oil to the new filter seal before screwing it on. 6. Screw the filter on until the gasket contacts the mounting plate. Then tighten the filter 1/2 to 2/3 of a turn. Note: Do not overtighten. 7. Add the specified oil to the crankcase. Responding to a Check-Engine Light Note: Engine-fault code information can be accessed by your Toro commercial products service staff only. g002373 Figure 36 1. Note the clearance between the fill device and the oil-fill neck. 8.
Changing the Fuel Filter Fuel System Maintenance Service Interval: Every 400 hours—Replace the fuel filter. Servicing the Fuel Filter/Water Separator Draining the Fuel Filter/Water Separator Service Interval: Before each use or daily—Drain water or other contaminants from the water separator. 1. 2. Place a clean container under the fuel filter (Figure 38). Loosen the drain plug on the bottom of the filter canister. 1.
Electrical System Maintenance Electrical System Safety • Disconnect the battery before repairing the machine. Disconnect the negative terminal first and the positive last. Connect the positive terminal first and the negative last. • Charge the battery in an open, well-ventilated area, away from sparks and flames. Unplug the charger before connecting or disconnecting the battery. Wear protective clothing and use insulated tools. decal115-7813 Figure 40 Servicing the Fuses 1. Power outlet (10 A) 5.
4. Start the engine in the machine providing the jump-start. Note: Let it run for a few minutes, then start your engine. 5. Remove the negative jumper cable first from your engine, then the battery in the other machine. 6. Install the battery cover to the battery base. Servicing the Battery Service Interval: Every 50 hours—Check the battery-fluid level (every 30 days if in storage). g010326 Figure 41 Every 50 hours—Check the battery cable connections. 1. Battery cover 2.
Changing the Front Differential Oil Drive System Maintenance 4-Wheel Drive Models Only Checking the Front Differential-Oil Level Service Interval: Every 800 hours (4-wheel drive models only). 4-Wheel Drive Models Only Differential oil specification: Mobil 424 hydraulic fluid Service Interval: Every 100 hours/Monthly (whichever comes first)—Check the level of the front differential oil (4-wheel drive models only). 1. Park the machine on a level surface. 2. Engage the parking brake. 3.
Adjusting the High-Low Cable Adjusting the Shift Cables Service Interval: After the first 10 hours Every 200 hours Service Interval: Every 200 hours 1. Move the shift lever to the NEUTRAL position. 1. 2. Remove the clevis pins securing the shift cables to the transaxle-shift arms (Figure 44). Remove the clevis pin securing the high-low cable to the transaxle (Figure 44). 2. Loosen the clevis jam nut and adjust the clevis so that the clevis hole aligns with the hole in the transaxle bracket. 3.
Inspecting the Tires Service Interval: Every 100 hours Checking the Front Wheel Alignment Front tires air pressure specification: 220 kPa (32 psi) Service Interval: Every 400 hours/Yearly (whichever comes first) Rear tires air pressure specification: 124 kPa (18 psi) 1. Ensure that the tires are facing straight ahead. 2. Measure the center-to-center distance (at axle height) at the front and rear of the steering tires (Figure 48).
Torquing the Wheel Lug Nuts Service Interval: After the first 2 hours After the first 10 hours Every 200 hours Wheel lug nut torque specification: 109 to 122 N∙m (80 to 90 ft-lb) Torque the lug nuts at the front and rear wheels in a crossing pattern as shown in Figure 50 to the specified torque. g010329 Figure 49 1. Tie rods 2. Jam nuts B. Rotate the tie rod to move the front of the tire inward or outward to achieve the center to center distances from front to back. C.
Cooling System Maintenance 3. Shut off the engine and remove the key. 4. Check the coolant level inside the reserve tank (Figure 51). Note: The coolant should be up to the bottom of the filler neck when the engine is cold. Cooling System Safety • Swallowing engine coolant can cause poisoning; keep out of reach from children and pets. • Discharge of hot, pressurized coolant or touching a hot radiator and surrounding parts can cause severe burns.
Removing Debris from the Cooling System 8. Changing the Engine Coolant Service Interval: Before each use or daily—Remove debris from the engine area and radiator. (Clean it more frequently in dirty conditions.) 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key. 4. Clean the engine area thoroughly of all debris. 5. Unlatch and remove the radiator screen from the front of the radiator (Figure 52).
Brake Maintenance Checking the Brake-Fluid Level Service Interval: Before each use or daily—Check the brake-fluid level. Check the brake-fluid level before you first start the engine. Every 1,000 hours/Every 2 years (whichever comes first)—Change the brake fluid. Brake-fluid type: DOT 3 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key. 4. Raise the hood to access to the master brake cylinder and reservoir (Figure 56).
g033488 Figure 59 1. Knob 3. Parking-brake lever 2. Set screw g002379 Figure 57 3. Rotate the knob (Figure 59) until a force of 20 to 22 kg (45 to 50 lb) is required to actuate the lever. 4. Tighten the set screw when finished (Figure 59). 1. Brake-fluid reservoir 6. If the fluid level is low, clean the area around the cap, remove the reservoir cap, and fill the reservoir to the proper level with the specified brake fluid (Figure 57).
Adjusting the Brake Pedal Service Interval: Every 200 hours Note: Remove the font hood to ease the adjustment procedure. 1. Remove the cotter pin and clevis pin securing the master cylinder yoke to the brake-pedal pivot (Figure 60). g036549 Figure 61 1. Clutch pedal 2. Brake pedal g002417 Figure 60 1. Master cylinder yoke 2. Brake-pedal pivot 2. Lift up on the brake pedal (Figure 61) until it contacts the frame. 3. Loosen the jam nuts securing the yoke to the master cylinder shaft (Figure 61).
Belt Maintenance Controls System Maintenance Adjusting the Alternator Belt Adjusting the Clutch Pedal Service Interval: After the first 10 hours—Check the condition and tension of the alternator belt. Note: You can adjust the clutch-pedal cable at the Every 200 hours—Check the condition and tension of the alternator belt. bell housing or at the clutch-pedal pivot. You can remove the front hood to easily access to the pedal pivot. 1.
Adjusting the Accelerator Pedal 1. Park the machine on a level surface, engage the parking brake, shut off the engine, and remove the key. 2. Adjust the ball joint on the accelerator cable (Figure 66) to allow 2.54 to 6.35 mm (0.100 to 0.250 inch) of clearance between the accelerator pedal arm and the top of the diamond tread floor plate (Figure 67), when you apply 11.3 kg (25 lb) of force to the center of the pedal. g009276 Figure 64 1. Clutch pedal 2. 9.2 to 9.
Converting the Speedometer Hydraulic System Maintenance You can convert the speedometer from mph to km/h or km/h to mph. 1. Hydraulic System Safety Park the machine on a level surface, engage the parking brake, shut off the engine, and remove the key. 2. Remove the hood; refer to Removing the Hood (page 37). 3. Locate the 2 loose wires next to the speedometer. 4. Remove the connector plug from the harness wire and connect the wires together.
Changing the Hydraulic Fluid and Cleaning the Strainer Servicing the Transaxle/Hydraulic System Service Interval: Every 800 hours—Change the hydraulic fluid and clean the strainer. Hydraulic-fluid capacity: 7 L (7.5 US qt) Transaxle/Hydraulic Fluid Specifications Transaxle-fluid type: Dexron III ATF Checking the Transaxle/Hydraulic-Fluid Level 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key. 4.
g010332 Figure 71 1. Hydraulic filter 2. High-flow hydraulic filter 6. Lubricate the gasket on the new filter. 7. Ensure that the filter mounting area is clean. 1. Hydraulic strainer 8. Screw the filter on until the gasket contacts the mounting plate, and tighten the filter 1/2 turn. 8. Install the strainer. 9. 9. Install the hydraulic hose and 90° fitting to the strainer in the same orientation. Start the engine and let it run for about 2 minutes to purge air from the system. 10.
Checking the High-Flow Hydraulic-Fluid Level Servicing the High-Flow Hydraulic System TC Models Only TC Models Only Service Interval: Before each use or daily—Check the high-flow hydraulic-fluid level (TC models only). (Check the level of hydraulic fluid before the engine is first started, and daily thereafter) Hydraulic Fluid Specifications The reservoir is filled at the factory with high-quality hydraulic fluid.
Changing the High-Flow Hydraulic Fluid and Filter Raising the Cargo Bed in an Emergency TC Models Only The cargo bed can be raised in an emergency without starting the engine by cranking starter or by jumping the hydraulic system. Service Interval: Every 1,000 hours—If you are using the recommended hydraulic fluid, replace the high-flow hydraulic filter. Raising the Cargo Bed using the Starter Every 2,000 hours—If you are using the recommended hydraulic fluid, change the high-flow hydraulic fluid.
g019543 Figure 75 1. Jumper hoses 7. Keep all bystanders away from the machines. 8. Start the second machine and move the lift lever to the raise position, which raises the disabled cargo bed. 9. Move the hydraulic-lift lever to the NEUTRAL position, and engage the lift-lever lock. g009822 Figure 73 1. Quick-coupler hose A 2. Quick-coupler hose B 10. 3. On the disabled machine, connect the 2 jumper hoses to the hoses that were disconnected (Figure 74). 4. Cap the unused fittings.
Cleaning Washing the Machine Wash the machine as needed using water alone or with a mild detergent. You may use a rag when washing the machine. Important: Do not use brackish or reclaimed water to clean the machine. Important: Do not use power-washing equipment to wash the machine. Power-washing equipment may damage the electrical system, loosen important decals, or wash away necessary grease at friction points. Avoid excessive use of water near the control panel, engine, and battery.
Storage A fully charged battery maintains its charge for about 50 days at temperatures lower than 4°C (40°F). If the temperatures will be above 4°C (40°F), check the water level in the battery and charge it every 30 days. Storage Safety • Shut off the machine, remove the key (if equipped), and wait for all movement to stop before you leave the operator’s position. Allow the machine to cool before adjusting, servicing, cleaning, or storing it.
Troubleshooting Problem Possible Cause Corrective Action The quick couplers are difficult to connector disconnect. 1. The hydraulic pressure not relieved (the quick coupler is under pressure). 1. Shut off the engine, move the hydraulic-lift lever forward and backward several times, and connect the quick couplers for the fittings in the auxiliary hydraulic panel. The power steering moves hard. 1. The hydraulic-fluid level is low. 1. Service the hydraulic reservoir. 2. The hydraulic fluid is hot. 3.
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
EEA/UK Privacy Notice Toro’s Use of Your Personal Information The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer.
The Toro Warranty Two-Year or 1,500 Hours Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for 2 years or 1,500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
