Form No. 3421-744 Rev A Workman® HDX-D Utility Vehicle with Bed Model No. Model No. Model No. Model No. Register at www.Toro.com. Original Instructions (EN) 07385—Serial No. 401420001 and Up 07385TC—Serial No. 401380001 and Up 07387—Serial No. 401420001 and Up 07387TC—Serial No.
Important: With your mobile device, you can scan the QR code on the serial number decal (if equipped) to access warranty, parts, and other product information. This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
Contents Servicing the Fuel Filter/Water Separator ...................................................... 43 Inspecting Fuel Lines and Connections............. 43 Electrical System Maintenance ........................... 44 Electrical System Safety ................................... 44 Servicing the Fuses .......................................... 44 Jump-Starting the Machine............................... 44 Servicing the Battery......................................... 45 Drive System Maintenance ......
Safety Improper use or maintenance by the operator or owner can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety-alert symbol (Figure 2), which means Caution, Warning, or Danger—personal safety instruction. Failure to comply with the instruction may result in personal injury or death. This machine has been designed in accordance with the requirements of SAE J2258.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decalbatterysymbols Battery Symbols Some or all of these symbols are on your battery. 1. Explosion hazard 6. Keep bystanders a safe distance away from the battery. 2. No fire, open flame, or smoking 7. Wear eye protection; explosive gases can cause blindness and other injuries. 3.
decal105-4215 105-4215 decal106-2355 1. Warning—avoid pinch points. 106-2355 1. Slow 2. Fast decal105-7977 105–7977 1. Tank 2. Pressure decal106-2353 106-2353 1. Electrical power point 6 3.
decal106-2377 106-2377 1. Locked 8. Warning—read the Operator's Manual. 2. Differential lock 9. Entanglement hazard, shaft—keep bystanders a safe distance away from the machine. 3. Unlocked 10. Retract hydraulics 4. Hydraulic lock 11. Extend hydraulics 5. Engage 12. Transmission—high speed 6. Power takeoff (PTO) 13. Transmission—low speed 7. Disengage 14. Parking brake decal106-6755 106-6755 1. Engine coolant under pressure. 3. Warning—do not touch the hot surface. 2.
decal115-2047 115-2047 1. Warning—do not touch the hot surface. decal106-7767 106-7767 1. Warning—read the Operator's Manual; avoid tipping the machine; wear the seat belt; lean away from the direction the machine is tipping. decal115-2281 115-2281 1. Headlights 4. Engine—run 2. Horn 5. Engine—start 3.
decal115-2282 115-2282 1. Warning—read the Operator's Manual. 2. Warning—stay away from moving parts, keep all guards and shields in place. 3. Crushing/dismemberment hazard of bystanders—keep bystanders a safe distance away from the machine, do not carry passengers in the cargo bed, keep arms and legs inside of the machine at all times, and use seat belts and handholds. decal115-7741 115-7741 1. Read the Operator’s Manual before servicing transmission fluid. decal115-7756 115-7756 decal115-7723 1.
decal115-7814 115-7814 decal117-2718 117-2718 decal121-6287 121-6287 1. Fill the reservoir with engine coolant to the bottom of the filler neck. decal121-6286 121-6286 1. Check the coolant level daily before use of the machine. Read the Operator's Manual before checking the engine-coolant level. 2. Do not open or add coolant to the radiator; doing so introduces air into the system and results in engine damage. Add only engine coolant to the reservoir.
decal121-9776 121-9776 1. Warning—read the Operator’s Manual and receive proper training before operating the machine. 4. Warning—engage the parking brake, shut off the engine, and remove the key from the key switch before walking away from the machine. 5. Tipping hazard—take turns slowly; drive slowly up and across cliffs; with no load, do not exceed 32 kph (20 mph); while carrying a load or when driving on uneven terrain, drive slowly. 2. Warning—wear hearing protection. 3.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Use Qty. Steering wheel 1 Install the steering wheel (TC models only). ROPS frame Flange-head bolt (1/2 x 1-1/4 inches) 1 6 Mount the Rollover Protection System (ROPS). No parts required – Check the fluid levels and tire pressure. No parts required – Burnish (break-in) the brakes. Note: Determine the left and right side of the machine from the normal operating position. 5.
2 3 Installing the Rollover Protection System (ROPS) Checking the Fluid Levels and Tire Pressure Parts needed for this procedure: No Parts Required 1 ROPS frame 6 Flange-head bolt (1/2 x 1-1/4 inches) Procedure 1. Check the engine-oil level before and after you first start the engine; refer to Checking the Engine-Oil Level (page 41). Procedure 1. Apply medium-grade (service-removable) thread-locking compound to the threads of the 6 flange-head bolts (1/2 x 1-1/4 inches). 2.
Product Overview Controls Become familiar with all the controls before you start the engine and operate the machine. Note: Determine the left and right sides of the machine from the normal operating position. Control Panel g036549 Figure 6 1. Clutch pedal 3. Accelerator pedal 2. Brake pedal Clutch Pedal You must fully press the clutch pedal (Figure 6) to disengage the clutch when starting the engine or shifting transmission gears.
Gear-Shift Lever Fully press the clutch pedal and move the shift lever (Figure 7) into the desired gear selection. A diagram of the shift pattern is shown below. g009160 Figure 7 g240581 Figure 8 Important: Do not shift the transaxle to the 1. Parking-brake lever 5. High-low range shifter REVERSE or FORWARD gear unless the machine is motionless; otherwise, you could damage the transaxle. 2. Hydraulic-bed lift 6. 4-wheel drive button (4-wheel drive models only) 3. Hydraulic-lift lock 7.
Hydraulic-Lift Lock Hour Meter The hydraulic-lift lock secures the lift lever, so that the hydraulic cylinders do not operate when the machine is not equipped with a bed (Figure 8). It also locks the lift lever in the ON position when using the hydraulics for attachments. The hour meter indicates the total hours of machine operation. The hour meter (Figure 5) starts to function whenever you rotate the key switch to the ON position or if the engine is running.
Tachometer Coolant-Temperature Gauge and Light The tachometer displays the speed of the engine (Figure 5 and Figure 9). The coolant-temperature gauge and light registers the coolant temperature in the engine and operates only when the key switch is in ON position (Figure 5). The indicator light blinks red if the engine overheats. Note: The white triangle indicates the desired engine speed for 540 rpm PTO operation. Charge Indicator The charge indicator illuminates when the battery discharges.
Passenger Handhold The passenger handhold is located on the dashboard (Figure 10). g009815 Figure 10 1. Passenger handhold 2. Storage compartment Seat-Adjustment Lever You can adjust the seat forward and rearward for your comfort (Figure 11). g021227 Figure 11 1.
Specifications Note: Specifications and design are subject to change without notice.
Checking the Tire Pressure Operation Service Interval: Before each use or daily Before Operation Front tires air pressure specification: 220 kPa (32 psi) Before Operation Safety Tear tires air pressure specification: 124 kPa (18 psi) General Safety Important: Check the tire pressure frequently to ensure proper inflation. If the tires are not inflated to the correct pressure, the tires will wear prematurely and may cause the 4-wheel drive to bind.
Adding Fuel Use only clean, fresh diesel fuel or biodiesel fuels with low (<500 ppm) or ultra-low (<15 ppm) sulfur content. The minimum cetane rating should be 40. Purchase fuel in quantities that can be used within 180 days to ensure fuel freshness. • Use summer grade diesel fuel (No. 2-D) at temperatures above -7°C (20°F) and winter grade (No. 1-D or No. 1-D/2-D blend) below that temperature.
Checking the Safety-Interlock System During Operation During Operation Safety Service Interval: Before each use or daily The purpose of the safety-interlock system is to prevent the engine from cranking or starting, unless you press the clutch pedal. General Safety • The owner/operator can prevent and is responsible CAUTION If the safety-interlock switches are disconnected or damaged, the machine could operate unexpectedly, causing personal injury. • Do not tamper with the safety-interlock switches.
• • • • • • • • • • • • Check carefully for overhead obstructions and do roll over if a wheel goes over the edge or if the edge gives way. When using the machine on public roads, follow all traffic regulations and use any additional accessories that may be required by law, such as lights, turn signals, slow-moving vehicle (SMV) signs, and others as required.
Loading and Dumping Safety Move the lever rearward to raise the cargo bed (Figure 15). • Do not exceed the gross vehicle weight (GVW) of the machine when operating it with a load in the cargo bed and/or towing a trailer; refer to Specifications (page 19). • Distribute the load in the cargo bed evenly to improve the stability and control of the machine. • Before dumping, ensure that there is no one behind the machine. • Do not dump a loaded cargo bed while the machine is sideways on a slope.
result. If engine fails to start after 10 seconds, turn the key to the OFF position. Check the controls and starting procedure, wait 10 additional seconds, and repeat the starting operation. Engaging the 4-Wheel Drive 4-Wheel Drive Models Only To enable automatic 4-Wheel Drive, press the top of the rocker switch into the 4X4 AUTO position (Figure 17). g026141 g227244 Figure 16 1. Latch handle Figure 17 3. Latch pin 1. 4x4 auto enable—on 2. 4x4 auto enable—off 2.
Driving the Machine Using the Differential Lock 1. Disengage the parking brake. 2. Fully press the clutch pedal. 3. Move the gear-shift lever to first gear. 4. Release the clutch pedal smoothly while pressing the accelerator pedal. 5. When the machine gains enough speed, remove your foot from the accelerator pedal, fully press the clutch pedal, move the gear-shift lever to the next gear, and release the clutch pedal while pressing the accelerator pedal. 6.
Using the Hydraulic Bed-Lift Lever to Control Hydraulic Attachments Using the Hydraulic Control The hydraulic control supplies hydraulic power from the machine pump whenever the engine runs. You can use the power through the quick couplers at the rear of the machine. • OFF Position This is the normal position for the control valve when it is not in use. In this position, the work ports of the control valve are blocked and any load is held by the check valves in both directions.
Troubleshooting the Hydraulic Control This position is similar to the LOWER (QUICK COUPLER B POSITION). It also directs hydraulic fluid to quick coupler B, except that the lever is held in this position by a detent lever in the control panel. This allows hydraulic fluid to flow continuously to equipment that use a hydraulic motor. • Difficulty in connecting or disconnecting quick couplers. The pressure is not relieved (the quick coupler is under pressure).
After Operation After Operation Safety General Safety • Allow the engine to cool before storing the machine in any enclosure. • Do not store the machine or fuel container where there is an open flame, spark, or pilot light, such as on a water heater or other appliance. g009821 Figure 20 • Keep all parts of the machine in good working 1. Axle condition and all hardware tightened. 2. Hitch plate • Replace all worn, damaged, or missing decals.
Towing a Trailer The machine is capable of pulling trailers and attachments of greater weight than the machine itself. Several types of tow hitches are available for the machine, depending on your application. Contact your Authorized Service Dealer for details. When equipped with a tow hitch bolted onto the rear axle tube, your machine can tow trailers or attachments with a maximum gross trailer weight (GTW) up to 1587 kg (3,500 lb).
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 2 hours • Torque the front and rear wheel lug nuts. After the first 10 hours • • • • • • After the first 50 hours • Change the engine oil and filter. • Adjust the engine-valve clearance. After the first 100 hours • Perform the guidelines for breaking in a new machine. Check the adjustment of the shift cables. Torque the front and rear wheel lug nuts.
Maintenance Service Interval Every 800 hours Every 1,000 hours Maintenance Procedure • • • • Change the front differential oil (4-wheel drive models only). Change the hydraulic fluid and clean the strainer. Replace the hydraulic filter. Change the high-flow hydraulic fluid and filter (TC models only). • Flush/replace the coolant system fluid. • Change the brake fluid. Note: Determine the left and right sides of the machine from the normal operating position.
Maintaining the Machine under Special Operating Conditions Important: If the machine is subjected to any of the conditions listed below, perform maintenance twice as frequently: • • • • • • Desert operation Cold climate operation—below 10°C (50°F) Trailer towing Frequent operation in dusty conditions Construction work After extended operation in mud, sand, water, or similar dirty conditions, have your brakes inspected and cleaned as soon as possible.
Using the Bed Support Important: Always install or remove the bed support from the outside of the bed. 1. Raise the bed until the lift cylinders are fully extended. 2. Remove the bed support from the storage brackets on the back of the ROPS panel (Figure 21). g009164 Figure 22 1. Bed support 3. Bed 2. Cylinder barrel 4. Remove the bed support from the cylinder, and insert it into the brackets on the back of the ROPS panel.
Installing the Full Bed Removing the Full Bed 1. Start the engine, engage the hydraulic-lift lever, and lower the bed until the cylinders are loose in the slots. 2. Release the lift lever and shut off the engine. 3. Remove the lynch pins from the outer ends of the cylinder rod clevis pins (Figure 23). Note: If you are installing the bed sides on the flat bed, it is easier to install them before installing the bed on the machine.
Raising the Machine DANGER A machine on a jack may be unstable and slip off the jack, injuring anyone beneath it. • Do not start the machine while the machine is on a jack, as the engine vibration or wheel movement could cause the machine to slip off the jack. • Always remove the key from the key switch before getting off the machine. • Block the tires when the machine is on a jack. g002370 Figure 25 1. Wear block 3.
3. Pivot the top of the hood forward and unplug the wire connectors from the headlights (Figure 28). 4. Remove the hood. Installing the Hood g009824 Figure 27 1. Rear jacking points Removing and Installing the Hood Removing the Hood 1. While grasping the hood in the headlight openings, lift up the hood to release the lower mounting tabs from the frame slots (Figure 28). g010314 Figure 28 1. Hood 2.
Lubrication Greasing the Bearings and Bushings Service Interval: Every 100 hours (lubricate more frequently in heavy-duty applications). Grease Type: No. 2 lithium grease 1. Use a rag to wipe the grease fitting clean so that foreign matter cannot be forced into the bearing or bushing. 2. With a grease gun, apply grease into the grease fittings on the machine. 3. g010571 Figure 30 Wipe any excess grease off the machine.
g010359 Figure 32 39
Engine Maintenance 4. Engine Safety Note: Holes in the filter appear as bright spots. Inspect the element for tears, an oily film, or damage to the rubber seal. If the filter is damaged, do not use it. • Shut off the engine, remove the key, and wait for all moving parts to stop before checking the oil or adding oil to the crankcase. Note: To prevent engine damage, always operate the engine with the air filter and cover installed.
Servicing the Engine Oil Note: Change the oil more frequently when operating conditions are extremely dusty or sandy. Note: Dispose of the used engine oil and oil filter at a certified recycling center. Engine-Oil Specifications Oil Type: Detergent engine oil (API SJ or higher) Crankcase Capacity: 3.2 L (3.4 US qt) when the filter is changed g028637 Viscosity: See the table below. Figure 35 1. Filler cap 2. Dipstick g016095 Figure 34 5.
5. Apply a light coat of clean oil to the new filter seal before screwing it on. 6. Screw the filter on until the gasket contacts the mounting plate. Then tighten the filter 1/2 to 2/3 of a turn. Note: Do not overtighten. 7. Add the specified oil to the crankcase. Responding to a Check-Engine Light Note: Engine-fault code information can be accessed by your Toro commercial products service staff only. g002373 Figure 36 1. Note the clearance between the fill device and the oil-fill neck. 8.
Changing the Fuel Filter Fuel System Maintenance Service Interval: Every 400 hours—Replace the fuel filter. Servicing the Fuel Filter/Water Separator Draining the Fuel Filter/Water Separator Service Interval: Before each use or daily—Drain water or other contaminants from the water separator. 1. 2. Place a clean container under the fuel filter (Figure 38). Loosen the drain plug on the bottom of the filter canister. 1.
Electrical System Maintenance Electrical System Safety WARNING CALIFORNIA Proposition 65 Warning Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. decal115-7813 Figure 40 1. Power outlet (10 A) 5. Lights/brake (15 A) 2. Switched power (10 A) 6. Hazard lights (10 A) 3. Fuel pump/supervisor switch (10 A) 7. 4WD/transmission (10 A) 4.
4. Start the engine in the machine providing the jump-start. Note: Let it run for a few minutes, then start your engine. 5. Remove the negative jumper cable first from your engine, then the battery in the other machine. 6. Install the battery cover to the battery base. Servicing the Battery Service Interval: Every 50 hours—Check the battery-fluid level (every 30 days if in storage). g010326 Figure 41 Every 50 hours—Check the battery cable connections. 1. Battery cover 2.
Changing the Front Differential Oil Drive System Maintenance 4-Wheel Drive Models Only Checking the Front Differential-Oil Level Service Interval: Every 800 hours (4-wheel drive models only). 4-Wheel Drive Models Only Differential oil specification: Mobil 424 hydraulic fluid Service Interval: Every 100 hours/Monthly (whichever comes first)—Check the level of the front differential oil (4-wheel drive models only). 1. Park the machine on a level surface. 2. Engage the parking brake. 3.
Adjusting the High-Low Cable Adjusting the Shift Cables Service Interval: After the first 10 hours Every 200 hours Service Interval: Every 200 hours 1. Move the shift lever to the NEUTRAL position. 1. 2. Remove the clevis pins securing the shift cables to the transaxle-shift arms (Figure 44). Remove the clevis pin securing the high-low cable to the transaxle (Figure 44). 2. Loosen the clevis jam nut and adjust the clevis so that the clevis hole aligns with the hole in the transaxle bracket. 3.
Inspecting the Tires Torquing the Wheel Lug Nuts Service Interval: Every 100 hours Front tires air pressure specification: 220 kPa (32 psi) Service Interval: After the first 2 hours After the first 10 hours Rear tires air pressure specification: 124 kPa (18 psi) Every 200 hours Wheel lug nut torque specification: 109 to 122 N∙m (80 to 90 ft-lb) Operating accidents, such as hitting curbs, can damage a tire or rim and also disrupt wheel alignment, so inspect the tire condition after an accident.
Cooling System Maintenance 3. Shut off the engine and remove the key. 4. Check the coolant level inside the reserve tank (Figure 49). Note: The coolant should be up to the bottom of the filler neck when the engine is cold. Cooling System Safety • Swallowing engine coolant can cause poisoning; keep out of reach from children and pets. • Discharge of hot, pressurized coolant or touching a hot radiator and surrounding parts can cause severe burns.
Removing Debris from the Cooling System 8. Changing the Engine Coolant Service Interval: Before each use or daily—Remove debris from the engine area and radiator. (Clean it more frequently in dirty conditions.) 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key. 4. Clean the engine area thoroughly of all debris. 5. Unlatch and remove the radiator screen from the front of the radiator (Figure 50).
Brake Maintenance Checking the Brake-Fluid Level Service Interval: Before each use or daily—Check the brake-fluid level. Check the brake-fluid level before you first start the engine. Every 1,000 hours/Every 2 years (whichever comes first)—Change the brake fluid. Brake-fluid type: DOT 3 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key. 4. Raise the hood to access to the master brake cylinder and reservoir (Figure 54).
g033488 Figure 57 1. Knob 3. Parking-brake lever 2. Set screw g002379 Figure 55 3. Rotate the knob (Figure 57) until a force of 20 to 22 kg (45 to 50 lb) is required to actuate the lever. 4. Tighten the set screw when finished (Figure 57). 1. Brake-fluid reservoir 6. If the fluid level is low, clean the area around the cap, remove the reservoir cap, and fill the reservoir to the proper level with the specified brake fluid (Figure 55).
Belt Maintenance Controls System Maintenance Adjusting the Alternator Belt Adjusting the Clutch Pedal Service Interval: After the first 10 hours—Check the condition and tension of the alternator belt. Note: You can adjust the clutch-pedal cable at the Every 200 hours—Check the condition and tension of the alternator belt. bell housing or at the clutch-pedal pivot. You can remove the front hood to easily access to the pedal pivot. 1.
Adjusting the Accelerator Pedal 1. Park the machine on a level surface, engage the parking brake, shut off the engine, and remove the key. 2. Adjust the ball joint on the accelerator cable (Figure 62) to allow 2.54 to 6.35 mm (0.100 to 0.250 inch) of clearance between the accelerator pedal arm and the top of the diamond tread floor plate (Figure 63), when you apply 11.3 kg (25 lb) of force to the center of the pedal. g009276 Figure 60 1. Clutch pedal 2. 9.2 to 9.
Converting the Speedometer Hydraulic System Maintenance You can convert the speedometer from mph to km/h or km/h to mph. 1. Hydraulic System Safety Park the machine on a level surface, engage the parking brake, shut off the engine, and remove the key. 2. Remove the hood; refer to Removing the Hood (page 37). 3. Locate the 2 loose wires next to the speedometer. 4. Remove the connector plug from the harness wire and connect the wires together.
High Viscosity Index/Low Pour Point Antiwear Hydraulic Fluid, ISO VG 46 Material Properties: • Viscosity—ASTM D445 cSt @ 40ºC: 44 to 48/cSt @ 100ºC: 7.9 to 8.5 • Viscosity index, ASTM D2270—140 to 152 • Pour point, ASTM D97— -35ºF to -46ºF • FZG, fail stage—11 or better • Water content (new fluid)—500 ppm (maximum) Industry Specifications: Vickers I-286-S, Vickers M-2950-S, Denison HF-0, Vickers 35 VQ 25 (Eaton ATS373-C) g002376 Figure 64 1. Dipstick 5.
11. Shut off the engine and attachment and check for leaks. Changing the Hydraulic Fluid and Cleaning the Strainer Service Interval: Every 800 hours Hydraulic-fluid capacity: 7 L (7.5 US qt) Hydraulic-fluid type: Dexron III ATF 1. 2. Park the machine on a level surface, engage the parking brake, shut off the engine, and remove the key. g002416 Figure 67 Remove the drain plug from the side of the reservoir, and let the hydraulic fluid flow into a drain pan (Figure 66). 1.
Material Properties: • Viscosity—ASTM D445 cSt @ 40ºC: 44 to 48/cSt @ 100ºC: 7.9 to 8.5 • Viscosity Index, ASTM D2270—140 to 152 • Pour Point, ASTM D97— -35ºF to -46ºF • FZG, Fail stage—11 or better • Water content (new fluid)—500 ppm (maximum) Industry Specifications: g010332 Figure 68 1. Hydraulic filter Vickers I-286-S, Vickers M-2950-S, Denison HF-0, Vickers 35 VQ 25 (Eaton ATS373-C) 2. High-flow hydraulic filter 4. Lubricate the gasket on the new filter. 5.
Raising the Cargo Bed in an Emergency The cargo bed can be raised in an emergency without starting the engine by cranking starter or by jumping the hydraulic system. Raising the Cargo Bed using the Starter Crank the starter while holding the lift lever in the Raise position. Run the starter for 10 seconds, then wait 60 seconds before engaging the starter again. If the engine does not crank, you must remove the load and bed (attachment) to service the engine or transaxle. g009822 Figure 69 1.
Cleaning Washing the Machine The machine should be washed as needed. Use water alone or with a mild detergent. A rag may be used when washing the machine. Important: Do not use power washing equipment to wash the machine. Power washing equipment may damage the electrical system, loosen important decals, or wash away necessary grease at friction points. Avoid excessive use of water near the control panel, engine, and battery. g019543 Figure 71 1. Jumper hoses 7.
Storage for about 50 days at temperatures lower than 4°C (40°F). If the temperatures will be above 4°C (40°F), check the water level in the battery and charge it every 30 days. Storage Safety • Let the engine cool before storing the machine. • Do not store the machine or fuel near flames or drain the fuel indoors. 13. Check and tighten all bolts, nuts, and screws. Repair or replace any part that is damaged. 14. Paint all scratched or bare metal surfaces.
Troubleshooting Problem Possible Cause Corrective Action The quick couplers are difficult to connector disconnect. 1. The hydraulic pressure not relieved (the quick coupler is under pressure). 1. Shut off the engine, move the hydraulic-lift lever forward and backward several times, and connect the quick couplers for the fittings in the auxiliary hydraulic panel. The power steering moves hard. 1. The hydraulic-fluid level is low. 1. Service the hydraulic reservoir. 2. The hydraulic fluid is hot. 2.
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
