Form No. 3390-347 Rev A Electric Bed Lift Kit 2014 and After Workman® MD/MDX/MDX-D Utility Vehicle Model No. 07389—Serial No. 315000001 and Up Installation Instructions Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger.
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description Use Qty. No parts required – Outboard-lift bracket (short flanges) Inboard-lift bracket (long flanges) Hex-head bolt (5/16 x 5-1/2 inch) Flange nut (5/16) Switch Fuse—15 amp Lift actuator Clevis pin (3-1/2 inch) Clevis pin (2-1/4 inch) Hairpin Hex-head bolt (1/2 x 5-1/2 inch) Locknut (1/2 inch) 1 1 1 1 1 1 1 1 1 2 1 1 No parts required – Prepare the machine.
WARNING A raised box could fall and injure persons that are working beneath it. • Always use the prop rod to hold the box up before working under the box. • Remove any load material from the box before raising it. 4. Remove the 4 flange nuts securing the latch-rod brackets to the underside of the box (Figure 2). Figure 3 1. Bolts (5/16 x 3/4 inch) 3. Lower-bed brace 2. Upper-bed brace 2. Remove the 2 left-most bolts (5/16 x 3/4 inch) that secure lower-bed brace to the bed (Figure 3).
(long flanges), bed structure, and the outboard bed-lift bracket (short flanges) as shown in Figure 5. Figure 6 1. Plugged hole 3. Cut the new hole (if required). 2. Bed-lift switch Figure 5 1. Locknuts (5/16 inch) 3. Plug the bed-lift switch into the harness connector in the dash. 3. Hex-head bolt (5/16 x 5-1/2 inch) 2. Hole 8 mm (5/16 inch) Note: Do not install the switch 4. Install a new thermal fuse (15 amp) into the open slot in the fuse block. 8.
. Press the up-paddle of the bed-lift switch to extend the actuator (Figure 6). Note: If the lift actuator does not extend, press the other paddle of the switch 6. Align the up-paddle to the 12 o’clock position and insert the bed-lift switch into the opening in the dash (Figure 6). Note: The switch should snap and lock into position 7.
outboard-lift brackets (Figure 9) and secure it with a nut (1/2 inch) until the flange nut is snug. 11. Tighten the flange nut that secure the bolt (5/16 inch) it is snug (Figure 5). 5 Removing the Prop Rod No Parts Required Procedure 1. Remove the hairpin and washer that secure the prop rod to the bottom of the bed (Figure 10). Figure 10 1. Washer 2. Hairpin 4. Bed hole 5. Prop rod 3. Slot (frame) 2. Slide the prop rod forward to remove it from the bracket on the frame (Figure 10).
Maintenance Operation Servicing the Air Cleaner on the Workman MDX-D WARNING Driving the machine with the cargo box raised may cause the machine to tip or roll easier. The box structure may become damaged if you operate the machine with the box raised. 1. Support the bed with lifting equipment. 2. Remove the hair pin cotter and clevis pin securing the actuator rod to the inboard and outboard-lift brackets (Figure 9). • Operate the machine only when the cargo box is down. 3. Tip the box all the way up.
Notes: 8
Notes: 9
Notes: 10
Declaration of Incorporation Model No. 07389 Serial No. Product Description Invoice Description General Description Directive 315000001 and Up Cab Kit, Workman MD/MDX/MDX-D Utility Vehicle ELECTRIC CARGO BED LIFT KIT (2014+) Utility Vehicle 2006/42/EC, 2000/14/EC Relevant technical documentation has been compiled as required per Part B of Annex VII of 2006/42/EC.
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
