Installation Instructions

ManualsBrandsToro ManualsVehiclesDoor Kit with Sliding Window, Workman HDX Utility Vehicle

FormNo.3385-461RevA

DoorKitwithSlidingWindow

Workman

MDXorHDXUtilityVehicle

ModelNo.07356

ModelNo.07393

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

PreparingtoInstalltheDoor

Kit

NoPartsRequired

Procedure

1.Movethemachinetoalevelsurfaceandsettheparking

brake.

2.Shutofftheengine,settheparkingbrake,andremove

thekeyfromtheignitionswitch.

InstallingtheDoors

Partsneededforthisprocedure:

1Right-handdoor

Left-handdoor

2Ballstud

Locknut(5/16inch)

2Doorstrut

4Washer

Procedure

1.Inserttheballstudthroughtherearholeinthebracket

onthecabframe,andinstallthelocknut(5/16inch)

ontotheballstud(Figure1).

Figure1

1.Locknut(5/16inch)

3.Frame

2.Bracket4.Ballstud

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3385-461*A

Summary of content (8 pages)

PAGE 1
Form No. 3385-461 Rev A Door Kit with Sliding Window Workman® MDX or HDX Utility Vehicle Model No. 07356 Model No. 07393 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. 2 Installation 1 Installing the Doors Preparing to Install the Door Kit No Parts Required Procedure 1. Move the machine to a level surface and set the parking brake. 2.
PAGE 2
. Install the 4 washers over the 4 hinge pins at the cab frame for the machine (Figure 2). 3. Install the door onto the hinge pins mounted on the cab frame (Figure 2). Figure 3 1. Ball stud (cab frame) 3. Fitting (strut cylinder) 2. Fitting (strut rod) 4. Ball stud (door frame) Note: The door-fitting strut has a quick-release end. Flip the lever vertically for installation. Once installed, close the lever to capture the ball stud (Figure 4). Figure 2 1. Door 2. Hinge pins 3. Washer 4.
PAGE 3
4 Assembling the Latch Pins Assembling the Door Lanyards Parts needed for this procedure: Parts needed for this procedure: 2 Hex nut (7/16 inch) 2 Lanyard 2 Latch pin 4 Shoulder bolt (5/16 x 1/2 inch) 2 Latch-pin cam 4 Locknut (5/16 inch) 4 Thrust washer 2 Pin guard Procedure 1. Assemble the lanyard to the door-frame hinge with a shoulder bolt (5/16 x 1/2 inch) and a locknut (5/16 inch) as shown in Figure 6. Procedure 1.
PAGE 4
Note: If the height measured is more than the zone specification, rotate the latch-pin cam 45° toward the inside of the cab to achieve the specified measurement. If the height measured is less than the zone specification, perform the opposite of the above procedure. 5 Adjusting the Door-latch Pin Note: The latch pin will self center. No Parts Required Procedure 1. Center the latch pin in the latch-pin-mount bracket on the rail (Figure 8). Figure 9 1. Bubble seal 2. Cab rail 4.
PAGE 5
Operating the Sliding Window Operation Open the latch to open and close the sliding window (Figure 11). Using the Door 1. Insert the key into the opening on the handle if the door is locked, and rotate the key to the open position (Figure 10). 2. Push the button on the handle and open the door (Figure 10). Figure 11 1. Window latch Figure 10 1. Key 2.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8