Operator's Manual

ManualsBrandsToro ManualsAttachmentsCE Hand Throttle Kit, Workman 3000 Series

FORM NO. 3317–613

EThe Toro Company-1995 TPS

INSTALLATION

INSTRUCTIONS

For Workman 3000 Series

HAND THROTTLE KIT

MODEL NO. 07436

1. Position vehicle on a clean, level surface, stop

engine, engage parking brake and remove key from

ignition switch. Disconnect positive cable from battery.

2. Mount slotted throttle rod ends to throttle levers with

shoulder bolts and locknuts, as shown in figure 1. Make

sure rod ends are mounted to sides of levers and bolt

shoulders are positioned in rod end slots.

Figure 1

1. Throttle levers

2. Throttle rod

3. Shoulder bolt

3. Locate (2) 1/4–20 x 5/8” lg. button head capscrews

and nuts securing dash panel to R.H. pedal support

(Right of horn button) (Fig. 2).

Figure 2

1. Dash panel

2. Pedal support

3. Button head capscrew

4. Horn button

4. Remove lower button head capscrew and nut and

discard. Do not remove top capscrew and nut.

5. Align mounting holes in back of hand throttle

assembly with (3) holes in dash. Large hole in back of

assembly fits over remaining screw head in dash panel.

6. Mount hand throttle assembly to dash and pedal

support with (3) 1/4–20 x 3/4” lg. capscrews and flange

locknuts supplied in kit (Fig. 3).

Figure 3

1. Hand throttle assembly

7. Move speed control lever to “hand throttle” side (left

slot) and push lever all the way upward (full speed).

8. Push accelerator pedal all the way to the floor and

hold or brace it there.

Figure 4

1. Throttle rod

2. Plastic fitting

3. Accelerator arm

4. Accelerator pedal

Summary of content (8 pages)

PAGE 1
FORM NO. 3317–613 INSTALLATION INSTRUCTIONS MODEL NO. 07436 HAND THROTTLE KIT For Workman 3000 Series 1. Position vehicle on a clean, level surface, stop engine, engage parking brake and remove key from ignition switch. Disconnect positive cable from battery. 2. Mount slotted throttle rod ends to throttle levers with shoulder bolts and locknuts, as shown in figure 1. Make sure rod ends are mounted to sides of levers and bolt shoulders are positioned in rod end slots. 4.
PAGE 2
9. While holding up hand throttle rod, rotate plastic rod fitting, on rod, up or down until holes in fitting align with hole in accelerator arm (Fig. 4). Secure fitting to accelerator arm with clevis pin and cotter pin. 3 1 10. Release accelerator pedal and move speed control lever to the “speed limiter” side (right slot) and fully upward to the “OFF” position.
PAGE 3
19. Remove (15) screws and washers securing front hood to vehicle frame and remove hood. 20. Insert end of harness with a male spade terminal, female spade terminal and wetherpak connector on it, up through opening in vehicle floor board, toward dash panel, following vehicle wire harness. Secure harness to vehicle wire harness with (2) cable ties. 21. Locate wire connected to “I” terminal of ignition switch. Remove wire from “I” terminal and plug into appropriate wire harness terminal.
PAGE 4
29. To assure proper operation of the parking brake switch the parking brake must be properly adjusted. Adjust parking brake as follows: 1 Loosen set screw securing knob to end of parking brake lever. Rotate knob until a force of 35–45 lbs. is required to actuate lever. 2 Tighten set screw after adjustment has been attained. 30. To adjust parking brake switch: Disengage parking brake. Move switch into parking brake lever until switch is activated, then tighten mounting nuts.
PAGE 5
SEE VEHICLE SCHEMATIC EXTRA A 3RD HIGH LOCKOUT SWITCH B S B I A Y SEE VEHICLE SCHEMATIC ELECTRICAL SCHEMATIC FOR HAND THROTTLE B 1/3 LIFT A X IGNITION SWITCH RUN ST ART A DIODE A B PARK BRAKE SWITCH N.C. B SPEED LIMITER SWITCH N.O.
PAGE 6
SEE VEHICLE SCHEMATIC EXTRA A 3RD HIGH LOCKOUT SWITCH B S B I A Y SEE VEHICLE SCHEMATIC 1/3 LIFT A ELECTRICAL SCHEMATIC FOR HAND THROTTLE AND GENERATOR 6 B X IGNITION SWITCH RUN ST ART A DIODE A B B B SPEED LIMITER SWITCH N.O. SEE GENERATOR SCHEMATIC PARK BRAKE SWITCH N.C.
PAGE 7
SEE VEHICLE SCHEMATIC EXTRA A 3RD HIGH LOCKOUT SWITCH SEE 1/3 LIFT SCHEMATIC B S B I A Y SEE VEHICLE SCHEMATIC 1/3 LIFT PARK BRAKE SEE 1/3 LIFT SWITCH CONNECTOR SCHEMATIC A X 1/3 LIFT "I" TERMINAL CONNECTOR IGNITION SWITCH RUN ST ART A DIODE A B PARK BRAKE SWITCH N.C. B SPEED LIMITER SWITCH N.O.
PAGE 8
SEE VEHICLE SCHEMATIC EXTRA A 3RD HIGH LOCKOUT SWITCH SEE 1/3 LIFT SCHEMATIC B S B I A Y SEE VEHICLE SCHEMATIC 1/3 LIFT PARK BRAKE SWITCH CONNECTOR SEE 1/3 LIFT SCHEMATIC A 1/3 LIFT "I" TERMINAL CONNECTOR X IGNITION SWITCH RUN ST ART A DIODE A B B B SPEED LIMITER SWITCH N.O. SEE GENERATOR SCHEMATIC PARK BRAKE SWITCH N.C. A ELECTRICAL SCHEMATIC FOR HAND THROTTLE, GENERATOR AND 1/3 LIFT.