Installation Instructions

ManualsBrandsToro ManualsVehiclesSteel Cargo Bed Base, Workman GTX Series Utility Vehicle

FormNo.3440-158RevA

SteelCargoBedBase

Workman

GTXSeriesUtilityVehicle

ModelNo.07450

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removeanexistingplasticcargobed.

Liftbracket

Flange-headbolt(3/8x2-1/2inches)

Locknut(3/8inch)

Installtheliftbracket.

Flatbedassembly1

Flange-headbolt(1/2x4-1/2inches)

Locknut(1/2inch)

Installtheatbedassembly.

Gasspring

Clevispin

Hairpincotter2

Spacer

Installthegasspring.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Shutoffthemachineandremovethekey.

g038447

Figure1

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3440-158*

Summary of content (8 pages)

PAGE 1
Form No. 3440-158 Rev A Steel Cargo Bed Base Workman® GTX Series Utility Vehicle Model No. 07450 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description Use Qty. No parts required – Prepare the machine. No parts required – Remove an existing plastic cargo bed.
PAGE 2
3. 2 Slide the prop rod forward out of the detent slot and remove the prop rod (Figure 3). Removing an Existing Plastic Cargo Bed No Parts Required Procedure g037393 Figure 3 If your machine is not equipped with a plastic cargo, you can skip to the next installation procedure. 1. Using an overhead hoist, raise the plastic cargo bed. 2. Remove the 3 flange-head bolts (5/16 x 3/4 inch) and prop rod U-bracket from the prop rod (Figure 2). 1. Detent slot 2. Prop rod 4.
PAGE 3
Installing the Lift Bracket Parts needed for this procedure: 1 Lift bracket 2 Flange-head bolt (3/8 x 2-1/2 inches) 2 Locknut (3/8 inch) 2. Secure the lift bracket to the rear and right frame tubes using the previously removed flange-head bolt and locknut and new 2 flange-head bolts (3/8 x 2-1/2 inches) and 2 locknuts (3/8 inch) as shown in Figure 6. 3. Torque the previously removed flange-head bolt and new 2 flange-head bolts (3/8 x 2-1/2 inches) to 41 N∙m (30 ft-lb). Procedure 1.
PAGE 4
Installing the Flat Bed Assembly Parts needed for this procedure: 1 Flat bed assembly 2 Flange-head bolt (1/2 x 4-1/2 inches) 2 Locknut (1/2 inch) Procedure 1. Move the flat bed rearward until the pivot-bracket assembly is aligned over the rear-frame channel. 2. Carefully lower the flat bed until the holes in the pivot brackets align with the mounting holes in the flat bed supports (Figure 7). 3.
PAGE 5
Installing the Gas Spring Parts needed for this procedure: 1 Gas spring 2 Clevis pin 2 Hairpin cotter 4 Spacer Procedure 1. Lift the flat bed assembly. 2. With the body side of the gas spring oriented toward the flat bed, secure the gas spring to the lift bracket using 2 clevis pins, 4 spacers, and 2 hairpin cotters (Figure 8). Ensure that you use the inner set of holes on the flat bed when securing the gas spring as shown in Figure 8. g340217 Figure 8 1. Clevis pin 4.
PAGE 6
3. 6 Loosen the 2 bolts on the bed-latch striker and move the striker up or down, depending on if the striker is too high or too low (Figure 10). Adjusting the Cargo Bed Latches No Parts Required Procedure If the cargo bed latch is out of adjustment, the cargo bed vibrates up and down as you drive the machine. You can adjust the latch posts to make the latches hold the cargo bed securely to the chassis. 1. 2. g034451 Figure 10 1. Bolt 2. Bed-latch striker Verify that the cargo bed is latching.
PAGE 7
Notes:
PAGE 8