Installation Instructions

ManualsBrandsToro ManualsRiding ProductsHood Guard, Outcross 9060 Series Traction Unit

FormNo.3426-500RevB

HoodGuard

Outcross9060SeriesTractionUnit

ModelNo.07531

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachineforinstallation.

Rightpivotguard1

Leftpivotguard

Hex-headbolt(5/8x1-3/4inches)

Locknut(5/8inch)

Installthepivotguards.

Hoodguard1

Largebumper2

Nut(M10)

Smallbumper

Flangenut(3/8inch)

Hex-headbolt(3/8x1-1/4inches)

Lockwasher1

Flatwasher1

Hex-headbolt(3/4x4inches)

Thrustwasher4

Locknut(3/4inch)

Pin1

Installthehoodguard.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.ShifttotheNEUTRALposition.

3.Lowerallattachments(ifequipped).

4.Engagetheparkingbrake.

5.Shutofftheengineandremovethekey.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3426-500*B

Summary of content (4 pages)

PAGE 1
Form No. 3426-500 Rev B Hood Guard Outcross 9060 Series Traction Unit Model No. 07531 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 Description Qty.
PAGE 2
Installing the Pivot Guards Parts needed for this procedure: 1 Right pivot guard 1 Left pivot guard 4 Hex-head bolt (5/8 x 1-3/4 inches) 4 Locknut (5/8 inch) g258730 Procedure Note: You must raise the radiator mount to install the pivot-guard hardware. 1. Loosen the hardware that secures the radiator mount to the frame. g269603 Figure 2 1. Locknut (5/8 inch) 3. Left pivot guard 2. Bumper side plate 4. Hex-head bolt (5/8 x 1-3/4 inches) 4. Gently lower the radiator mount to the frame. 5.
PAGE 3
Installing the Hood Guard Parts needed for this procedure: 1 Hood guard 2 Large bumper 2 Nut (M10) 1 Small bumper 1 Flange nut (3/8 inch) 1 Hex-head bolt (3/8 x 1-1/4 inches) 1 Lock washer 1 Flat washer 2 Hex-head bolt (3/4 x 4 inches) 4 Thrust washer 2 Locknut (3/4 inch) 1. Large bumper 5. Flat washer 1 Pin 2. Small bumper 6. Pin 3. Locknut (M10) 7. Lock washer 4. Hex-head bolt (3/8 x 1-1/4 inches) 8. Flange nut (3/8 inch) g258763 Figure 3 Procedure 1.
PAGE 4
g268999 Figure 4 1. Hex-head bolt (3/4 x 4 inches) 3. Pin 2. Locknut (3/4 inch) 4. Thrust washers 3. Install the pin through the left side of the hood guard and the left pivot guard (Figure 4). Operation Lowering the Hood Guard The pin holds the hood guard in a raised position. To lower the hood guard, remove the pin (Figure 5). g269000 Figure 5 1.