Installation Instructions

ManualsBrandsToro ManualsRiding Products7-Way Trailer Plug Kit (EU), Outcross 9060 Series Traction Unit

FormNo.3435-347RevA

7-WayTrailerPlugKit(EU)

Outcross9060SeriesTractionUnit

ModelNo.07538

InstallationInstructions

Installation

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.ShifttotheNEUTRALposition.

3.Loweranyequippedattachments.

4.Engagetheparkingbrake.

5.Removethebed;refertoyourmachine

Operator’sManual.

6.Disconnectthebattery;refertotheelectrical

systemmaintenancesectionofyourOperator’s

Manual.

InstallingtheWireHarness

Partsneededforthisprocedure:

1Trailer-plugwireharness

1Mountbracket

Bolt(1/4x3/4inch)

Nut(1/4inch)

Bolt(#10x1-1/4inch)

Nut(#10)

Procedure

Note:Determinetheleftandrightsidesofthe

machinefromthenormaloperatingposition.

1.Use2bolts(1/4x3/4inch)and2nuts(1/4inch)

tosecurethemountbrackettotheframeonthe

leftsideofthemachine(Figure1).

g293471

Figure1

1.Machine-wire-harness

connector

4.Trailer-plugwireharness

connector—TRAILERHITCH

2.Trailer-plugwire-harness

connector—TOFRAME

HARNESS

5.Bolt(#10x1-1/4inch)and

nut(#10)

3.Bolt(1/4x3/4inch)and

nut(1/4inch)

6.Mountbracket

2.Use3bolts(#10x1-1/4inch)and3nuts(#10)

tosecuretheendofthetrailer-plugwireharness

labeledTRAILERHITCHtothemountbracket

(Figure1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3435-347*A

Summary of content (4 pages)

PAGE 1
Form No. 3435-347 Rev A 7-Way Trailer Plug Kit (EU) Outcross 9060 Series Traction Unit Model No. 07538 Installation Instructions Installation 1. 1 Use 2 bolts (1/4 x 3/4 inch) and 2 nuts (1/4 inch) to secure the mount bracket to the frame on the left side of the machine (Figure 1). Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Shift to the NEUTRAL position. 3. Lower any equipped attachments. 4. Engage the parking brake. 5.
PAGE 2
3. Route and connect the end of the wire harness labeled TO FRAME HARNESS to the frame-harness connector as shown in Figure 1. 3 Installing the Switch Parts needed for this procedure: 1 Switch g267650 Procedure 1. Figure 3 1. Switch Remove the screws that secure the control panel to the dashboard (Figure 2). 3. 8-socket connector—REAR POWER SW 2. Knockout area 4. Insert the switch into the panel (Figure 3). 5.
PAGE 3
4 Installing the Brake-Light Relay Parts needed for this procedure: 1 Relay wire harness 1 Relay 1 Cable tie Procedure g302388 Figure 6 If you do not have an electric brake controller (shown in Figure 5) installed, you must install the brake-light relay and wire harness. 1. Relay wire harness 4. Relay 2. Frame tube 5. Machine-wire-harness connector—BRAKE CONTROL MODULE 6. Fuse block 3. Cable tie g263573 Figure 5 1. Brake controller Refer to Figure 6 for this procedure. 1.
PAGE 4
5 6 Installing the Fuse Completing the Installation Parts needed for this procedure: No Parts Required 1 Fuse (15 A) 1 Fuse (20 A) Procedure • Connect the battery; refer to the electrical system maintenance section of your machine Operator’s Manual. Procedure 1. 2. Install the fuse (15 A) to the rear auxiliary power port of the machine fuse block. Refer to the table below and Figure 6.