Installation Instructions

ManualsBrandsToro ManualsRiding ProductsHorn Kit, Outcross 9060 Series Traction Unit

FormNo.3427-831RevA

HornKit

Outcross9060SeriesTractionUnit

ModelNo.07549

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Horn-switchassembly(switchandjam

nut)

Rubberbutton1

Installthehornswitch.

Nopartsrequired

–

Installthehorn.

Fuse(10A)

Installthefuse.

Nopartsrequired

–

Connectthebattery.

Nopartsrequired

–

Testthehornfunction.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3427-831*A

Summary of content (8 pages)

PAGE 1
Form No. 3427-831 Rev A Horn Kit Outcross 9060 Series Traction Unit Model No. 07549 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 No parts required 2 Horn-switch assembly (switch and jam nut) Rubber button 1 No parts required – Install the horn. Fuse (10 A) 1 Install the fuse. No parts required – Connect the battery. No parts required – Test the horn function.
PAGE 2
. 1 Carefully lift the steering column-panel from the dash (Figure 2). Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface, move the shift lever to the NEUTRAL position, and lower the attachments. 2. Engage the parking brake, shut off the engine, and remove the key. 3. Disconnect the battery; refer to the electrical system maintenance section of the traction unit Operator’s Manual. g254488 Figure 2 Installing the Horn Switch 1.
PAGE 3
Connecting the Horn Switch 3 Connect the 2-socket connector of the machine wire harness labeled HORN SWITCH onto the blade connector of the horn switch (Figure 4). Installing the Horn No Parts Required Assembling the Horn to the Machine g272242 Figure 4 1. Blade connector (switch) 2. 2-socket connector (HORN SWITCH) g254486 Figure 6 Installing the Steering-Column Panel 1. 1. Align the holes in the steering-column panel with the holes in the dash (Figure 5).
PAGE 4
Connecting the Wire Harness to the Horn (5/16 inch), and torque the bolt and nut to 1978 to 2542 N∙cm (175 to 225 in-lb). Connect the terminal receptacles for the yellow and black wires onto the blade terminals of the horn (Figure 9). Note: You can connect either wire to either blade terminal of the horn. g254491 Figure 8 1. Bolt (frame/bracket 5/16 x 2-3/4 inches) 3. Flange locknut (5/16 inch) 2. Bracket (horn) g254484 Figure 9 1. Terminal receptacle (yellow wire) 2.
PAGE 5
4 5 Installing the Fuse Connecting the Battery Parts needed for this procedure: No Parts Required 1 Fuse (10 A) Procedure Connect the battery; refer to the electrical system maintenance section of the traction unit Operator’s Manual. Procedure Insert the fuse (10 A) into the fuse block slot at row 4, column C. 6 Testing the Horn Function No Parts Required Procedure g256221 1. Insert the key into the key switch and rotate it clockwise to the ON position. 2. Press and release the horn button.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8