Form No. 3422-108 Rev A Canopy Extension Kit Workman® GTX Utility Vehicle Model No. 07920—Serial No. 400000000 and Up Installation Instructions Installation 1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key. 4. Disconnect the battery; refer to your Operator’s Manual. 5. Raise the cargo bed to the dump position and secure it with the prop rod.
Installing the Rear Mounting Tubes to the Existing Canopy Parts needed for this procedure: 2 Rear mounting tube 4 Carriage bolt (5/16 x 3-1/2 inches) 4 Flange nut (5/16 inch) Procedure Secure the 2 rear mounting tubes to the existing canopy rear tubes using the 4 carriage bolts (5/16 x 3-1/2 inches) and 4 flange nuts (5/16 inch) as shown in Figure 1. g261411 Figure 1 1. Carriage bolt (5/16 x 3-1/2 inches) 3. Flange nut (5/16 inch) 2. Existing canopy rear tube 4.
If you are installing on a 2-person canopy (Model 07921), install rear mounting tubes in the bottom holes on the existing rear tubes (Figure 2). If you are installing on a 4-person canopy (Model 07922), install rear mounting tubes in the top holes on the existing rear tubes (Figure 2). g261563 Figure 2 1. Holes for 2-person canopy (Model 07921) 2.
3 Installing the Support Brackets Parts needed for this procedure: 2 Support bracket 8 Hex-washer head bolt (5/16 x 3/4 inch) Procedure Secure the 2 support brackets to the rear mounting tubes using 8 hex-washer head bolts (5/16 x 3/4 inch) as shown in Figure 3. g261414 Figure 3 Left side shown 1. Rear mounting tube 3. Support bracket 2.
4 Installing the Canopy Extension Parts needed for this procedure: 1 Canopy extension 1 Canopy support bracket 6 Sealing washer 6 Locknut (1/4 inch) 2 Flange-head bolt (1/4 x 2-1/4 inches) 4 Flange-head bolt (1/4 x 1-3/4 inches) 1 Trim seal 2 Spacer Procedure 1. Place the canopy extension on top of the installed rear tube mounts (Figure 4).
2. Secure the canopy extension using 4 flange-head bolts (1/4 x 1-3/4 inches), 4 sealing washers, and 4 locknuts (1/4 inch) as shown in Figure 5. g261704 Figure 5 1. Locknut (1/4 inch) 3. Flange-head bolt (1/4 x 1-3/4 inches) 2. Sealing washer 4. Canopy extension 3. Install the trim seal onto the canopy support bracket (Figure 6).
4. Secure the canopy support bracket to the canopy extension using 2 flange-head bolts (1/4 x 2-1/4 inches), 2 spacers, 2 sealing washers, and 2 locknuts (1/4 inch) as shown in Figure 7. g261478 Figure 7 1. Locknut (1/4 inch) 4. Canopy support bracket 2. Sealing washer 5. Flange-head bolt (1/4 x 2-1/4 inches) 3.
5 Installing the Rain Gutter Parts needed for this procedure: 1 Rain gutter 10 Plastic rivet Procedure 1. Secure the rain gutter to the canopy extension side using 5 plastic rivets (Figure 8). Note: The orientation of the holes differ on each side of the rain gutter. Ensure that the holes align with the canopy extension before installing the plastic rivets. g261725 Figure 8 1. Rain gutter 2.
2. Using the rain gutter as the template, drill 5 holes (6.4 mm or 1/4 inch) into the front canopy (Figure 9). g261568 Figure 9 3. Secure the rain gutter to the front canopy side using 5 plastic rivets (Figure 10). g261569 Figure 10 1. Rain gutter 2.
6 Connecting the Battery No Parts Required Procedure Connect the battery; refer to your Operator’s Manual.
Notes:
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
