Form No. 3421-992 Rev B 2-Person or 4-Person Canopy Kit Workman® GTX Utility Vehicle Model No. 07921—Serial No. 400000000 and Up Model No. 07922—Serial No. 400000000 and Up Installation Instructions Installation 1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key. 4. Disconnect the battery; refer to your Operator’s Manual. 5.
3 4 Installing the Front Mounting Tubes Removing the Side Panels No Parts Required Parts needed for this procedure: 2 Front mounting tube 2 Flange-head bolt (5/16 x 3 inches) 2 Spacer (5/8 x 1 inch) 4 Flange nut (5/16 inch) 2 Carriage bolt (5/16 x 2 inches) For Gasoline Machines Important: Before performing this procedure, check your machine to see if the holes for installation already exist. If not, proceed with this procedure. Note: Retain all the hardware that you remove in this procedure.
. Disconnect the vent tube and fuel line from the tank (Figure 4). 6. Remove the 4 screws securing the left side panel to the lower seat assembly (Figure 6). Note: Prepare to capture and clean up any fuel that spills when you disconnect the fuel line from the tank. DANGER In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. • Drain the fuel from the fuel tank when the engine is cold.
8. Remove the 2 flange-head bolts securing the battery tray to the frame (Figure 8). g035126 Figure 9 1. Right side panel 2. Self-tapping screw g033999 Figure 8 1. Flange-head bolt 2. 3. Right side panel 2. Self-tapping screw 9. Remove the 2 bolts securing the charger bracket to the battery tray (Figure 10). Remove the 4 screws securing the right side panel to the lower seat assembly (Figure 8).
Drilling the Support Bracket No Parts Required Procedure Drill the support bracket using the measurements shown in Figure 11. When you drill the highest upper hole, ensure that you drill all the way through the outer bracket, frame tube, and firewall. CAUTION Use caution when drilling the holes into the right side of the frame on an electric machine. If you drill too far, you could damage the batteries or other components.
Installing the Side Panels No Parts Required For Gasoline Machines 1. Secure the right side panel using the previously removed 4 screws (Figure 8). 2. Secure the battery tray to the frame using the previously removed 2 flange-head bolts (Figure 8). 3. Secure the battery cables using the previously removed 2 bolts and 2 nuts and connect the battery terminals (Figure 7). 4. Secure the left side panel using the previously removed 4 screws (Figure 6). 5.
Installing the Rear Mounting Tubes and Tube-Mounting Bracket 2. Secure the tube-mounting bracket to the rear mounting tubes using 2 flange-head bolts (5/16 x 3 inches) and 2 flange nuts (5/16 inch) as shown in Figure 13. 3. Install the trim seal onto the tube-mounting bracket (Figure 13).
Installing the Long Canopy Support Brackets For a 4-Person Canopy Only Parts needed for this procedure: 2 Long canopy support bracket 8 Hex-washer head bolt (5/16 x 3/4 inch) 2 Trim seal Procedure 1. Secure the 2 long canopy support brackets to the front and rear mounting tubes using 8 hex-washer head bolts (5/16 x 3/4 inch) as shown in Figure 14. 2. Install the 2 trim seals onto the 2 long canopy support brackets (Figure 14).
Installing the Canopy Parts needed for this procedure: 1 Canopy 4 Flange-head bolt (1/4 x 1-3/4 inches) 4 Sealing washer 4 Locknut (1/4 inch) Procedure Important: If you are installing a mirror kit, install it before installing the canopy. Secure the canopy to the front and rear mounting tubes using 4 flange-head bolts (1/4 x 1-3/4 inches), 4 sealing washers, and 4 locknuts (1/4 inch) as shown in Figure 15. g259844 Figure 15 2-person canopy shown 1. Sealing washer 3. Canopy 2.
Installing the Canopy Support Bracket Parts needed for this procedure: 1 Canopy support bracket 2 Flange-head bolt (1/4 x 2-1/4 inches) 2 Locknut (1/4 inch) 2 Sealing washer 1 Trim seal 2 Spacer (1/4 inch) Procedure 1. Install the trim seal onto the tube-mounting bracket (Figure 16).
2. Secure the canopy support bracket to the front support tubes and canopy using the 2 flange-head bolts (1/4 x 2-1/4 inches), 2 spacers (1/4 inch), 2 sealing washers, and 2 locknuts (1/4 inch) as shown in Figure 17. g259846 Figure 17 2-person canopy shown 1. Locknut (1/4 inch) 4. Flange-head bolt (1/4 x 2-1/4 inches) 2. Sealing washer 5. Canopy support bracket 3.
11 Installing the Canopy Support Tube For a 4-Person Canopy Only Parts needed for this procedure: 1 Canopy support tube 6 Locknut (1/4 inch) 2 Sealing washer 2 Flange-head bolt (1/4 x 1-1/2 inches) 1 Foam pad 4 Flange-head bolt (1/4 x 1-1/4 inches) Procedure 1. Apply the foam pad to the canopy support tube (Figure 18).
2. Secure the canopy support tube to the long canopy support brackets using 4 flange-head bolts (1/4 x 1-1/4 inches) and 4 locknuts (1/4 inch) as shown in Figure 19. g262068 Figure 19 1. Long canopy support bracket 3. Locknut (1/4 inch) 2. Flange-head bolt (1/4 x 1-1/4 inches) 4. Canopy support tube 3. Using the canopy support tube as the template, drill 2 holes (6 mm or 1/4 inch) into the canopy. 4.
Notes:
Notes:
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
