Form No. 3452-390 Rev A Beacon Kit Workman® UTX Passenger Utility Vehicle Model No. 08132 Installation Instructions Important: You must install the Overhead Console Kit (Model 08130) before you install this kit. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 2 No parts required – Prepare the machine. No parts required – Remove the bolt from the canopy, if necessary.
5. 1 Disconnect the negative (-) battery cable from the battery post. Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Shift the transmission lever to the P (PARK) position. 3. Shut off the engine and remove the key. 4. Wait for the engine to cool completely. g365494 Figure 2 1. Negative (-) battery cable g364252 Figure 1 2 2.
2 Removing the Bolt from the Canopy If Necessary No Parts Required Procedure Important: If you already installed the canopy and routed the wire harness from the Overhead Console Kit (Model 08130) to the rear, left of the canopy, skip this procedure and proceed to 3 Removing the Console and Routing the Wire Harness (page 4).
3 Removing the Console and Routing the Wire Harness If You Previously Installed the Overhead Console Kit Only No Parts Required Procedure 1. If you already installed the Overhead Console Kit and routed the wires marked BEACON, skip this step and proceed to step 2. Remove the 8 screws securing the overhead console and remove the overhead console (Figure 4). Retain the 8 screws and overhead console for later installation. g363607 Figure 4 2.
3. If you already performed this step, skip this step and proceed to step 5. Route the wire-harness leg with the 2 spade terminals toward the left, rear area of the roll-bar posts (Figure 6). g364200 Figure 6 1. Spade terminals 4. Install the previously removed console using the 8 screws (Figure 4). Torque the 8 screws to 339 N∙cm (30 in-lb). 5. Route the female 8-socket connector labeled BEACON SWITCH through the opening where you removed the console switch bracket (Figure 7).
4 Installing the Beacon Switch Parts needed for this procedure: 1 Beacon switch Procedure 1. From the under side of the cab controls panel, press the plug out of the hole shown in Figure 8. 2. Install the switch into the console-switch bracket (Figure 8). g383739 Figure 8 1. Plug 2.
3. Align the console-switch bracket into the opening and connect the rocker switch to the female 8-socket connector (Figure 9). g383738 Figure 9 4. Secure the previously removed console-switch bracket to the overhead console (Figure 5). Torque the 4 screws to 11.3 N∙m (100 in-lb). 5. Connect the beacon switch to the wire-harness connector labeled BEACON SWITCH into the hole in the control panel (Figure 8).
5 Installing the Beacon Mount Parts needed for this procedure: 1 Beacon mount 2 Bolt 2 Nuts Procedure Use 2 bolts and 2 nuts to secure the bracket to the left-side rear lifting point of the roll bar as shown in Figure 10.
6 Installing the Beacon Parts needed for this procedure: 1 Beacon 1 Beacon socket assembly Procedure 1. Remove the beacon connector from the beacon socket (Figure 11). 2. Route the wire harness up through the jam nut, washer, beacon mount, beacon socket, and connect it to the beacon connector (Figure 11). 3. Install the beacon connector into the beacon socket by rotating the beacon socket (Figure 11). Note: This will prevent twisting of the wire harness. 4.
7 8 Installing the Canopy Connecting the Battery No Parts Required No Parts Required Procedure Procedure Secure the previously removed canopy using the bolts, washers, and spacers (Figure 3). Connect the negative (-) battery cable to the battery post. g365493 Figure 12 1. Negative (-) battery cable 10 2.
Operation Operating the Beacon Switch Down position—Off Up position—On 11
