Installation Instructions

ManualsBrandsToro ManualsVehiclesBeacon Kit, Workman UTX Passenger Utility Vehicle

FormNo.3448-173RevA

BeaconKit

Workman

UTXPassengerUtilityVehicle

ModelNo.08132

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removethecanopy.

Nopartsrequired

–

Removetheconsole(ifyoupreviously

installedtheoverheadconsolekitonly)

androutethewireharness.

Beaconswitch1Installthebeaconswitch.

Beaconmount1

Bolt2

Nuts2

Installthebeaconmount.

Beacon1

Beaconsocketassembly1

Installthebeacon.

Nopartsrequired

–

Installthecanopy.

Important:YoumustinstalltheOverheadConsoleKit(Model08130)beforeyouinstallthiskit.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.ShiftthetransmissionlevertotheP(Park)position.

3.Shutofftheengineandremovethekey.

4.Disconnectthenegative(-)batterycablefromthebatterypost.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3448-173*

Summary of content (8 pages)

PAGE 1
Form No. 3448-173 Rev A Beacon Kit Workman® UTX Passenger Utility Vehicle Model No. 08132 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 2 No parts required – Prepare the machine. No parts required – Remove the canopy. 3 No parts required – Remove the console (if you previously installed the overhead console kit only) and route the wire harness.
PAGE 2
Removing the Canopy No Parts Required Procedure Remove the bolts, washers, and spacers securing the canopy (Figure 1) and remove the canopy. Retain the canopy, bolts, washers, and spacers. g363987 Figure 1 2-person canopy shown 1. Canopy 3. Sealing washer 2. Hex-head bolt (1/4 x 1-1/4 inches) 4.
PAGE 3
Removing the Console and Routing the Wire Harness If You Previously Installed the Overhead Console Kit Only No Parts Required Procedure 1. Remove the 8 screws securing the overhead console and remove the overhead console (Figure 2). Retain the 8 screws and overhead console for later installation. g363607 Figure 2 2. Remove the console-switch bracket from the overhead console (Figure 3). Retain the bracket and 4 screws for later installation. g364119 Figure 3 3.
PAGE 4
g364200 Figure 4 1. Spade terminals 4. Install the previously removed console using the 8 screws (Figure 2). Torque the 8 screws to 339 N∙cm (30 in-lb). 5. Route the female 8-socket connector labeled BEACON SWITCH through the opening where you removed the console switch bracket (Figure 5).
PAGE 5
4 Installing the Beacon Switch Parts needed for this procedure: 1 Beacon switch Procedure 1. From the under side of the cab controls panel, press the plug out of the hole shown in Figure 6. g364024 Figure 6 1. Plug 2. Switch 2. Install the switch into the console-switch bracket (Figure 6). 3. Align the console-switch bracket into the opening and connect the rocker switch to the female 8-socket connector (Figure 7).
PAGE 6
g364199 Figure 7 4. Secure the previously removed console-switch bracket to the overhead console (Figure 3). Torque the 4 screws to 11.3 N∙m (100 in-lb). 5. Connect the beacon switch to the wire-harness connector labeled BEACON SWITCH into the hole in the control panel (Figure 6).
PAGE 7
6 Installing the Beacon Parts needed for this procedure: 1 Beacon 1 Beacon socket assembly Procedure 1. Remove the beacon connector from the beacon socket (Figure 9). 2. Route the wire harness up through the jam nut, washer, beacon mount, beacon socket, and connect it to the beacon connector (Figure 9). 3. Install the beacon connector into the beacon socket by rotating the beacon socket (Figure 9). Note: This will prevent twisting of the wire harness. 4.
PAGE 8
Connecting the Battery No Parts Required Procedure Connect the negative battery cable to the battery post. Operation Operating the Beacon Switch Press the beacon switch to activate and deactivate the beacon.