Installation Instructions

ManualsBrandsToro ManualsVehiclesElectric Bed Lift Kit, Workman UTX Passenger Utility Vehicle

FormNo.3448-185RevB

ElectricBedLiftKit

Workman

UTXPassengerUtilityVehicle

ModelNo.08134

InstallationInstructions

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.ShiftthetransmissionlevertotheP(Park)

position.

3.Shutofftheengineandremovethekey.

4.Disconnectthenegative(-)batterycablefrom

thebatterypost.

InstallingtheSwitch

NoPartsRequired

Procedure

1.Raisethehood(Figure1).

Themachinewire-harnessconnector(labeled

BOXLIFTSW.)fortheswitchislocatedunderthe

hoodandneartheheadlightandhazardlight

switches.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3448-185*

Summary of content (8 pages)

PAGE 1
Form No. 3448-185 Rev B Electric Bed Lift Kit Workman® UTX Passenger Utility Vehicle Model No. 08134 Installation Instructions 1 2 Preparing the Machine Installing the Switch No Parts Required No Parts Required Procedure Procedure 1. Park the machine on a level surface. 2. Shift the transmission lever to the P (Park) position. 3. Shut off the engine and remove the key. 4. Disconnect the negative (-) battery cable from the battery post.
PAGE 2
g364304 Figure 2 1. Plug 3. 2. Switch Install the switch through the opening in the dashboard (Figure 2). Ensure that the switch is oriented properly. 4. g361798 Figure 1 2. Remove the plastic cover from the dashboard (Figure 2). Note: Discard the plastic cover. 2 Install the machine wire-harness connector (labeled BOX LIFT SW.) to the switch.
PAGE 3
Removing the Existing Bed Cylinder No Parts Required Procedure 1. Raise the cargo bed; refer to the Raising the Cargo Bed procedure in your machine Operator’s Manual. 2. Remove the clevis pins and hairpin cotters that secure the existing cylinder to the bed and the machine frame (Figure 3). g364508 Figure 3 1. Hairpin cotter 3. Clevis pin 2. Bed cylinder 3. Remove the existing bed cylinder from the machine.
PAGE 4
Installing the Lift Cylinder No Parts Required Procedure 1. Install the lift cylinder to the rear frame bracket using a clevis pin and hairpin cotter (Figure 4). g364633 Figure 5 1. Hairpin cotter g364627 Figure 4 1. Lift cylinder 3. Hairpin cotter 2. Clevis pin 2. Connect the wire-harness connector labeled BOX LIFT ACTUATOR to the lift cylinder. Note: The wire-harness connector is located near the crosslink that is above the engine. 3.
PAGE 5
Operation WARNING Driving the machine with the cargo bed raised may cause the machine to tip or roll over, causing possible injury to you and/or bystanders and damage to the cargo bed. • Operate the machine only when the cargo bed is down. • After dumping the contents in the cargo bed, lower the bed. CAUTION The bed may be heavy and could crush your hands or other body parts. Keep your hands and other body parts clear when lowering the bed.
PAGE 6
Notes:
PAGE 7
Declaration of Incorporation Model No. 08134 Serial No. Product Description Invoice Description N/A and Up Electric Bed Lift Kit, Workman UTX Passenger Utility Vehicle ELECTRIC BED LIFT [WM UTX] General Description Directive Utility Vehicle 2006/42/EC, 2014/30/EU Relevant technical documentation has been compiled as required per Part B of Annex VII of 2006/42/EC.
PAGE 8