Form No. 3423-437 Rev A Manual Blade Sand Pro®/Infield Pro® 3040 and 5040 Traction Unit Model No. 08714—Serial No. 400900001 and Up Register at www.Toro.com.
serious injury or death if you do not follow the recommended precautions. Introduction g000502 Figure 2 Safety-alert symbol Important: To maximize the safety, performance, and proper operation of this machine, carefully read and fully understand the contents of this Operator’s Manual. Failing to follow these operating instructions or to receive proper training may result in injury. For more information on safe operating practices, including safety tips and training materials, go to www.Toro.com.
Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal93-9879 93-9879 1. Stored energy hazard—read the Operator's Manual.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 Description Use Qty.
Media and Additional Parts Description Use Qty. 1 Operator’s Manual Read the manual before installing the blade. Note: Determine the left and right sides of the machine from the normal operating position.
Installing the Pivot Bracket and the Locking Pedal on a Machine with Holes that Align with the Bushing Plate and the Pivot Bracket g209719 Figure 5 g210450 1. Footrest 3. Locknut (5/16 inch) 2. Pivot bracket 4. Carriage bolt (5/16 x 3/4 inch) 2. Using the pivot bracket as a drilling template, drill 3 holes (8 mm or 5/16 inch) into the flange of the footrest (Figure 6). g209724 g252120 Figure 6 Figure 4 1. Bushing plate 3. 1.
g209721 Figure 8 6. Assemble the pivot bracket to the footrest (Figure 9) with 3 hex-head bolts (5/16 x 3/4 inch) and 3 locknuts (5/16 inch). g210469 Figure 10 1. Spacer (5/8 x 1-1/16 inches) 8. 2. Pivot shaft (locking pedal) Align the locking pedal to the left footrest and the holes in the pivot bracket (Figure 11). g210468 Figure 11 9. g209720 Figure 9 1. Locknut (5/16 inch) 3. Bracket 2. Hex-head bolt (5/16 x 3/4 inch) 7.
g210470 Figure 12 1. Locknut (5/16 inch) 3. Pivot bracket 2. Bushing plate 4. Carriage bolt (5/16 x 3/4 inch) 10. 11. Torque the locknuts to 71 to 92 N∙cm (100 to 130 in-lb) g252374 Figure 13 Slide the torsion spring onto the bushing plate while hooking 1 end of the spring onto the small stud on the locking pedal and pressing the other end against the floor plate (Figure 13). Note: Position the spring onto the bushing plate as shown. 1. Locknut (1/4 inch) 3. Bushing plate 2. Torsion spring 4.
Installing the Hub Assembly and the Locking Pedal on a Machine with Holes that Align with the Hub Assembly Note: Do not overtighten the nut; the locking pedal must pivot freely when pressed. g210450 g210333 Figure 15 1. Nut (5/8 inch) 3. Pivot shaft 2. Washer (5/8 x 1 inch) g252121 Figure 16 1. Hub assembly 1. 9 Install the hub assembly to the left footrest with 2 bolts (5/16 x 3/4 inch) and 2 locknuts (5/16 inch).
g252125 g252122 Figure 17 1. Locknut (5/16 inch).) 4. Bolt (5/16 x 3/4 inch) 2. Locknut (1/4 inch) 5. Washer (9/32 inch) 3. Hub assembly 6. Bolt (1/4 x 2-3/4 inch) 2. Secure the bottom of the hub assembly to the machine frame with a bolt (1/4 x 2-3/4 inch), a washer (1/4 inch), and a locknut (1/4 inch); refer to Figure 17. 3. Torque the locknuts to 71 to 92 N∙cm (100 to 130 in-lb) 4. Align the locking pedal to the left footrest and the holes in the hub assembly (Figure 18).
9. Secure the locking pedal to the footrest and the hub assembly with a flat washer (5/8 x 1 inch) and locknut (5/8 inch); refer to Figure 21. Note: Do not overtighten the nut; the locking pedal must pivot freely when pressed. g252126 Figure 21 1. Nut (5/8 inch) 3. Pivot shaft 2. Washer (5/8 x 1 inch) Discard the parts that were not necessary for your machine.
Procedure 3 Note: Make sure that the front and rear tires are inflated to 28 to 41 kPa (4 to 6 psi). Installing the Mounting Brackets 1. Parts needed for this procedure: 2. 2 Mounting bracket assembly 4 Bolt (1/2 x 3-1/2 inches) 4 Locknut (1/2 inch) Block up the rear of the machine and remove the rear tires. Note: Position the blocks under the rear wheel motor mounts.
Procedure 4 Installing the Lift Arms 1. Position the lift arms so that the mounting hole of each lift arm bracket aligns with the holes in the mounting brackets (Figure 23). 2. Secure the right lift arm to the mounting bracket with a clevis pin and hairpin cotter pin (Figure 23). 3. Parts needed for this procedure: 1 Right lift arm 1 Left lift arm Loosely install one end of the torsion tube to the right lift arm with 2 bolts (3/8 x 1 inch) and locknuts (3/8 inch); refer to Figure 23.
Procedure 5 Note: Optionally, you can purchase a 60-inch blade. Install it as directed for the 40-inch blade in this section. Installing the Blade 1. Parts needed for this procedure: 1 40-inch blade (optionally, you can purchase and install the 60-inch blade) 2 Brace plate 2 Bolt (3/8 x 1 inch) 6 Locknut (3/8 inch) 4 Bolt (3/8 x 3 inches) Loosely secure a brace plate to each of the inner mounting tabs on the blade assembly. Note: Position the brace plates as shown in Figure 24. 2.
g025725 Figure 24 1. Lift arms 4. Inner mounting tab (2) 2. Brace plate 5. Blade mounting bracket 3.
6 Installing the Lift-Arm Foot Pedal Parts needed for this procedure: 1 Lift-arm foot pedal 2 Bolt (3/8 x 3 inches) 4 Locknut (3/8 inch) 2 Spring bracket 2 Bolt (3/8 x 2-3/4 inches) 2 Extension spring 2 Spring rod g025724 Figure 26 Procedure 1. Mount the lift-arm foot pedal to the outside of the left lift arm with 2 bolts (3/8 x 3 inch) and 2 locknuts (3/8 inch). Note: Position the foot pedal as shown in Figure 25. 1. Spring bracket 3. Extension spring 2. Spring rod 4. Lift arm 4.
Operation 7 Operating the Blade Adjusting the Spring Tension Pull back on the handle to raise and lock the blade into the transport position. Press the locking pedal to release the blade into the operating position. You can use the blade to push or pull sand and dirt. With the blade in the operating position, simply push forward or pull back slightly on the handle or press on the lift arm foot pedal to control the plowing action.
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 08714 Serial No.
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
