Operator's Manual

ManualsBrandsToro ManualsRiding ProductsFinish Drag Kit, Nail Drag for Sand Pro 2040Z Traction Unit

FormNo.3378-567RevA

FinishDragKit

NailDragforSandPro

2040ZTractionUnit

ModelNo.08718

Operator'sManual

Introduction

Readthisinformationcarefullytolearnhowtooperateand

maintainyourproductproperlyandtoavoidinjuryand

productdamage.Youareresponsibleforoperatingthe

productproperlyandsafely.

YoumaycontactTorodirectlyatwww .Toro.comforproduct

andaccessoryinformation,helpndingadealer,ortoregister

yourproduct.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelnumberofyour

productready.

Thismanualidentiespotentialhazardsandhassafety

messagesidentiedbythesafetyalertsymbol(

Figure1),

whichsignalsahazardthatmaycauseseriousinjuryordeath

ifyoudonotfollowtherecommendedprecautions.

Figure1

1.Safetyalertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanicalinformation

andNoteemphasizesgeneralinformationworthyofspecial

attention.

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Chain

Chainsleeve

Bolt(3/8x1-1/4inch)

Washer8

Locknut4

Installthechains.

Bolt(3/8x1-1/4inch)

Washer8

Locknut4

Installthedragmat.

Carrier

Bolt(3/8x3/4inch)

Locknut4

Installthecarriers.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3378-567*A

Summary of content (4 pages)

PAGE 1
Form No. 3378-567 Rev A Finish Drag Kit Nail Drag for Sand Pro® 2040Z Traction Unit Model No. 08718 Operator's Manual Introduction Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register your product.
PAGE 2
Note: If the top plates, the nail plate, and the nails are currently installed on the nail drag, remove them; refer to the nail drag Operator’s Manual. 2. Secure the chain to the bracket with a bolt (3/8 x 1-1/4 inch), 2 washers, and a locknut, as shown in Figure 3. 3. Repeat steps 1 and 2 for the other side. Installing the Chains Installing the Carriers 1. Slide a chain sleeve over each chain (Figure 2). 1 1.
PAGE 3
Product Overview 1 2 3 4 G024018 Figure 6 G023726 Figure 5 2. Add or remove weights as necessary. 1. Front weights (2 included) 3. Chain with sleeve (2) 2. Carrier (2) 4. Drag mat 3. Secure the weights with the 2 bolts and the 2 nuts. The Finish Drag Mat includes 2 longer bolts to accommodate the additional weights that it requires.
PAGE 4
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 08718 Serial No.