Operator's Manual

ManualsBrandsToro ManualsRiding ProductsFinish Brush Kit, Flex Tooth Rake for Sand Pro 2040Z Traction Unit

FormNo.3378-580RevA

FinishBrushKit

FlexToothRakeforSandPro

2040ZTractionUnit

ModelNo.08719

Operator'sManual

Introduction

Readthisinformationcarefullytolearnhowtooperateand

maintainyourproductproperlyandtoavoidinjuryand

productdamage.Youareresponsibleforoperatingthe

productproperlyandsafely.

YoumaycontactTorodirectlyatwww .Toro.comforproduct

andaccessoryinformation,helpndingadealer,ortoregister

yourproduct.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelnumberofyour

productready.

Thismanualidentiespotentialhazardsandhassafety

messagesidentiedbythesafetyalertsymbol(

Figure1),

whichsignalsahazardthatmaycauseseriousinjuryordeath

ifyoudonotfollowtherecommendedprecautions.

Figure1

1.Safetyalertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanicalinformation

andNoteemphasizesgeneralinformationworthyofspecial

attention.

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Weight2Installtheweights.

Brushassembly(left-hand)

Brushassembly(right-hand)

Screw(1/4x1-1/4inch)

Locknut(1/4inch)

Installthesidebrushes.

Brushassembly(center)

Screw(1/4x7/8inch)

Locknut(1/4inch)

Installthecenterbrush.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3378-580*A

Summary of content (4 pages)

PAGE 1
Form No. 3378-580 Rev A Finish Brush Kit Flex Tooth Rake for Sand Pro® 2040Z Traction Unit Model No. 08719 Operator's Manual Introduction Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register your product.
PAGE 2
Installing the Weights Before installing the finish brush kit, ensure that there are 6 weights installed on the front of the machine; refer to Installing and Removing the Weights (page 3). Installing the Side Brushes 1. Remove the screw and the locknut on the end of 1 of the rake side assemblies as shown in Figure 2. G024630 Figure 4 1 Installing the Center Brush 1. Remove the 2 screws and the 2 locknuts near the center of the rake center assembly as shown in Figure 5. 2 G024613 1 Figure 2 1.
PAGE 3
Product Overview 1. Remove the 2 bolts and 2 nuts securing the existing weights on the front of the machine (Figure 9). Note: If the machine is equipped with the light kit, remove the nut and the bolt securing the front light to the machine. Retain all of the parts; refer to the Light Kit Installation Instructions. 1 4 3 2 G024629 Figure 7 1. Weights (2 included) 3. Center brush assembly 2. Right-hand brush assembly 4.
PAGE 4
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 08719 Serial No.