Operator's Manual

ManualsBrandsToro ManualsAttachmentsRear Broom, Sand Pro/Infield Pro 3040 and 5040 Traction Unit

FormNo.3427-609RevA

RearBroom

SandPro

/IneldPro

3040and5040TractionUnit

ModelNo.08753—SerialNo.260000001andUp

Operator'sManual

Introduction

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoid

injuryandproductdamage.Youareresponsiblefor

operatingtheproductproperlyandsafely.

Visitwww.Toro.comformoreinformation,including

safetytips,trainingmaterials,accessoryinformation,

helpndingadealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineT oroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.Figure1

identiesthelocationofthemodelandserialnumbers

ontheproduct.Writethenumbersinthespace

provided.

g003440

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhas

safetymessagesidentiedbythesafety-alertsymbol

(Figure2),whichsignalsahazardthatmaycause

seriousinjuryordeathifyoudonotfollowthe

recommendedprecautions.

g000502

Figure2

Safety-alertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

Contents

Introduction...............................................................1

Safety.......................................................................2

SafetyandInstructionalDecals..........................2

Setup........................................................................3

1AssemblingtheLiftArm/Attachment

AdaptertotheRearBroom..............................3

2MountingtheRearBroomtotheTraction

Unit.................................................................4

3RemovingtheRearBroomfromthe

TractionUnit....................................................5

4AdjustingtheLinkAssembly............................5

ProductOverview.....................................................6

Operation..................................................................7

AdjustingtheRearBroomAngle.........................7

AdjustingtheBroomHeadAngle........................7

SettingtheTransportPosition.............................8

Attachments/Accessories...................................8

OperatingTips....................................................9

Maintenance...........................................................10

InspectingandCleaningtheBroomand

TractionUnit..................................................10

GreasingtheAttachmentAdapter.....................10

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedinMexico

AllRightsReserved

*3427-609*A

Summary of content (12 pages)

PAGE 1
Form No. 3427-609 Rev A Rear Broom Sand Pro®/Infield Pro® 3040 and 5040 Traction Unit Model No. 08753—Serial No. 260000001 and Up Operator's Manual Introduction g000502 Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. Visit www.Toro.
PAGE 2
Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal106-5517 106-5517 1. Warning—do not touch the hot surface.
PAGE 3
Setup 1 Assembling the Lift Arm/Attachment Adapter to the Rear Broom Parts needed for this procedure: Rear broom assembly 1 Drawbar assembly 1 Bolt (3/8 x 1 inch) 1 Bolt (1/2 x 1-3/4 inches) 1 Flange nut (1/2 inch) 1 Hex nut (1/2 inch) 1. Rear broom assembly 5. Flange nut (1/2 inch) 1 Flange nut (3/8 inch) 2. Drawbar assembly 6. Hex nut (1/2 inch) 1 Lift arm/attachment adapter assembly 3. Bolt (3/8 x 1 inch) 7. Flange nut (3/8 inch) g274944 Figure 3 Some parts not shown for clarity 4.
PAGE 4
2 Mounting the Rear Broom to the Traction Unit Parts needed for this procedure: g266521 Figure 5 1. Attachment adapter 4. Bolt (3/8 x 1-1/4 inches) 2. Pivot bar 5. Locknut (3/8 inch) 3. Large cotter pins 6. Handle 3. 4. 2 Bolt (3/8 x 2-1/2 inches) 4 Washer (3/8 x 7/8 inch) 2 Spacer 2 Locknut (3/8 inch) Procedure Secure the pivot bar (Figure 5) with 3 cotter pins, a bolt (3/8 x 1-1/4 inches), and a locknut (3/8 inch). 1. Remove any attachment from the rear of the machine. 2.
PAGE 5
g005342 Figure 8 1. Locking lever 2. Adapter handle g220791 Figure 7 1. Tube frame of the traction unit 2. Long arm of the lift arm assembly 5. Spacer 3. Bolt (3/8 x 2-1/2 inches) 7. Locknut (3/8 inch) 6. Chain 2. Lower the traction unit adapter. 3. Grasp the adapter handle and lift the attachment adapter while pivoting it back onto the attachment (Figure 8). Note: If the attachment adapter becomes stuck 4.
PAGE 6
Product Overview 4 Adjusting the Link Assembly No Parts Required Procedure 1. With the rake mounted and secured on the traction unit, raise the attachment. 2. Measure the gap between the heavy washer and the shoulder of the lift yoke on the attachment adapter as shown in Figure 10. g003463 Figure 11 Note: The link is adjusted correctly if you measure a gap—1.5 to 2 mm (0.060 to 0.080 inch) between the heavy washer and the lift-yoke shoulder (Figure 10). g220790 Figure 10 1. Jam nut 4.
PAGE 7
Adjusting the Broom Head Angle Operation Adjusting the Rear Broom Angle You can change the angle of the broom heads in respect to the ground. You can change the angle of the broom to increase or decrease its aggressiveness in the sand. Mount the broom pivot to the bottom holes in the attachment adapter brackets for less aggressive raking or the top holes for more aggressive raking (Figure 12). 1. Loosen the nut and bolt securing the broom head pivot brackets (Figure 14). 2.
PAGE 8
Setting the Transport Position Complete the following procedure to increase the height of the broom when transporting: 1. Lower the broom and lift assembly as far down as possible. 2. Disconnect the chains from the lift arms and reconnect them higher. Note: To ensure the proper operation of the broom, the chains must be returned to the original slack position before operating.
PAGE 9
Operating Tips Read this section before raking a trap. Many conditions affect the which adjustments are necessary; the texture and depth of the sand, moisture content, weeds, the amount of compaction can all vary from course to course and trap to trap. Make the adjustments on the broom for optimum results in your particular area. Raking Speed Practice raking in a large and level trap. Practice starting and stopping, turning, raising and lowering the broom, and entering and leaving the trap.
PAGE 10
Maintenance Inspecting and Cleaning the Broom and Traction Unit Service Interval: After each use Clean the machine thoroughly after use. Because sand is extremely abrasive, the sand should be flushed off after each use. If the machine is cleaned frequently, (before the sand has a chance to cake), it can be cleaned with a stream of water from a hose with the nozzle removed. A high pressure stream could drive the sand into wear areas where it could act as a grinding compound.
PAGE 11
Notes:
PAGE 12