Form No. 3364-397 Rev A Debris Blower Sand Pro/Infield Pro 3040 and 5040 Traction Unit Model No. 08759—Serial No. 310000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
(Figure 2), which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions. Introduction This product complies with all relevant European directives, for details please see the separate product specific Declaration of Conformity (DOC) sheet. Figure 2 The debris blower is mounted to a ride-on machine which is intended to be used by professional, hired operators in commercial applications.
Safety Hazard control and accident prevention are dependent upon the awareness, concern, and proper training of the personnel involved in the operation, transport, maintenance, and storage of the machine. Improper use or maintenance of the machine can result in injury or death. To reduce the potential for injury or death, comply with the following safety instructions. • Before Operating • Read and understand the contents of this Operator’s Manual before operating the machine.
• To reduce a potential fire hazard, keep the engine free of excessive grease, grass, leaves, and accumulations of dirt. Never wash a warm engine or any electrical parts with water. • Be sure that the machine is in safe operating condition by keeping nuts, bolts, and screws tight. Check the fan shaft bearing mounting bolts and nuts frequently to be sure that they are tightened to specification.
106-5517 1. Warning—do not touch the hot surface. 105-4593 1. Entanglement hazard, shaft—do not remove cover while parts are moving, keep all guards in place.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description 1 2 3 Use Qty. Debris blower assembly 1 Mount the debris blower to the traction unit No parts required – Adjust the link assembly No parts required – Grease the blower Media and Additional Parts Description Use Qty.
4. Pivot the locking lever to the right to lock the adapters together. 3 5. Connect the attachment hydraulic hose couplers to the hydraulic couplers on the traction unit rear remote hydraulics kit. Grease the Blower Important: Whenever the hydraulic hose couplers are disconnected, make sure the dust plugs are installed to prevent contamination from entering either hydraulic system. Procedure 2 Before the Debris Blower is operated, it must be greased to assure proper lubrication.
Product Overview Operation Specifications Adjust Discharge Opening Note: Specifications and design are subject to change without notice. The discharge opening (Figure 5) is adjustable to increase or decrease air output velocity and volume. Decreasing discharge opening size will increase velocity. Net weight 235 lb. (107 kg) 1. Loosen discharge opening deflector mounting screws (Figure 5).
1 G003783 Figure 6 1.
Maintenance Bearing Alignment If the motor mounting brackets are ever removed, they must be realigned before the debris blower is operated. Refer to the Part Catalog for the Alignment Tool part number. Lubrication The debris blower has (2) fan shaft bearings that must be lubricated regularly. The bearings are located on each side of the blower housing. If the machine is operated under normal conditions, lubricate bearings with No.
Torquing Fasteners If the blower is ever disassembled, the following fasteners must be torqued as specified. Also, apply Loctite 242 to the threads before installing. • The set screws securing the motor and fan shaft couplers (Figure 10) must be torqued to 58 to 82 in-lb. • The fan shaft bearing set screws (Figure 11) must be torqued to 58 to 82 in-lb. G003816 1 Figure 11 1. Set screw • The fan mounting nut (Figure 12) must be torqued to 500 ft-lb. 1 G003817 Figure 12 1.
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro® Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
