Operator's Manual

ManualsBrandsToro ManualsAttachmentsQAS Nail Drag, Sand Pro/Infield Pro 3040 and 5040 Traction Unit

FormNo.3443-815RevA

QASNailDrag

SandPro

/IneldPro

3040and5040TractionUnit

ModelNo.08761—SerialNo.270000001andUp

Operator'sManual

Introduction

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoid

injuryandproductdamage.Youareresponsiblefor

operatingtheproductproperlyandsafely.

Visitwww.Toro.comformoreinformation,including

safetytips,trainingmaterials,accessoryinformation,

helpndingadealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineT oroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.Figure1

identiesthelocationofthemodelandserialnumbers

ontheproduct.Writethenumbersinthespace

provided.

g006212

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhas

safetymessagesidentiedbythesafety-alertsymbol

(Figure2),whichsignalsahazardthatmaycause

seriousinjuryordeathifyoudonotfollowthe

recommendedprecautions.

g000502

Figure2

Safety-alertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3443-815*

Summary of content (8 pages)

PAGE 1
Form No. 3443-815 Rev A QAS Nail Drag Sand Pro®/Infield Pro® 3040 and 5040 Traction Unit Model No. 08761—Serial No. 270000001 and Up Operator's Manual Introduction Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. Visit www.Toro.
PAGE 2
Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal106-5517 106-5517 1. Warning—do not touch the hot surface.
PAGE 3
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. Nail drag 1 Mount the nail drag. No parts required – Adjust the link assembly. No parts required – Grease the nail drag. Mounting the Nail Drag Adjusting the Link Assembly Note: Determine the left and right sides of the machine from the normal operating position. 1. Remove any attachment from the rear of the machine. 2.
PAGE 4
Greasing the Nail Drag Operation Before operating the nail drag, grease it; refer to Lubricating the Machine (page 6). Operating the Nail Drag Important: Failure to properly grease the unit will • The amount the drag nails engage in the ground result in premature failure of critical parts. determines the scarifying depth. • To adjust the amount the nails engage in the ground proceed as follows: 1. Remove the lynch pins from the clevis pins (Figure 5). g006213 Figure 5 4 2.
PAGE 5
Inspecting and Cleaning the Nail Drag When the scarifying operation is completed, clean the machine thoroughly. Since this machine is used primarily in extremely abrasive conditions, the material should be flushed off after each use. If the machine is cleaned frequently, it can be cleaned with a stream of water from a hose with the nozzle removed. A high pressure stream could drive the sand into wear areas where it could act as a grinding compound.
PAGE 6
Maintenance Lubricating the Machine Service Interval: Every 100 hours The nail drag has bushings that must be lubricated regularly. The bushings are located in the frame hub; lubricate the grease fitting immediately after every washing, regardless of the interval listed. g006211 Figure 7 Greasing the Attachment Adapter If the locking lever on the attachment adapter does not pivot freely and easily, apply a light coat of grease to the area shown in Figure 8.
PAGE 7
Optional Equipment Quick-attach system groomer kit Model No. 08762 Automat kit (requires quick-attach system groomer kit, Model 08762) Model No. 08763 Manual drag mat kit Model No.
PAGE 8
The Toro Warranty Two-Year or 1,500 Hours Limited Warranty Parts Conditions and Products Covered The Toro Company warrants your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for 2 years or 1,500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).