Installation Instructions

ManualsBrandsToro ManualsAttachmentsAuto Drag Mat Kit, Sand Pro/Infield Pro 3040 and 5040 Traction Unit with QAS Nail Drag

FormNo.3393-140RevA

Auto-MatKit

SandPro

/IneldPro

3040and5040TractionUnit

ModelNo.08763—SerialNo.315000001andUp

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Introduction

YoumaycontactTorodirectlyatwww .Toro.comforproduct

safetyandoperationtrainingmaterials,accessoryinformation,

helpndingadealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelandserialnumbersof

yourproductready.Figure1illustratesthelocationofthe

modelandserialnumbersontheproduct.Writethenumbers

inthespaceprovided.

Figure1

1.Locationofthemodelandserialnumbers

ModelNo.

SerialNo.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Wearpad1

Liftarm

Hex-head-angebolt(3/8x1-1/4inches)

Flangenut(3/8inch)

Connectionlift

Liftbeam

Chain

Carriagebolt(5/16x1inch)

Flatwasher(3/8inch)

Flangenut(5/16inch)

Cotterpin(5/32x1-1/4inches)

Pivotbar1

Flangebearing2

Installthelift-armassembly.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3393-140*A

Summary of content (8 pages)

PAGE 1
Form No. 3393-140 Rev A Auto-Mat Kit Sand Pro®/Infield Pro® 3040 and 5040 Traction Unit Model No. 08763—Serial No. 315000001 and Up Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Introduction Figure 1 You may contact Toro directly at www.Toro.
PAGE 2
Description Slide-lock bracket Clevis pin (1/2 x 4-1/2 inches) Flat washer (17/32 inch) Hairpin cotter Drag tongue Cotter pin (1/8 x 1 inch) Shackle Hex-head bolt (1/4 x 2-1/2 inches) Spacer Locknut (1/4 inch) Hex-head-flange bolt (3/8 x 1-1/4 inches) Flange nut (3/8 inch) Drag mat Clevis pin (3/8 x 1-1/8 inches) Lanyard Crossmember bracket Cotter pin (15/16 x 3/4 inch) Clevis pin (3/8 x 3/4 inch) Drag-mat, side bracket Drag-mat, bottom bracket Hex-head bolt (3/8 x 1 inch) Zinc spacer (0.382 x 0.
PAGE 3
Assembling and Installing the Lift-Arm Assembly of the quick-attach coupler to the left side of the lift arm (Figure 3). 1. Attach the wear pad to the lift-arm with 2 hex-head flange bolts (3/8 x 1-1/4 inches) and 2 flange nuts (3/8 inch) as shown in Figure 2. Figure 3 1. Lift-arm assembly 4. Pivot bar 2. Cotter pin—5/32 x 1-1/4 inches (3) 5. Flange nut (3/8 inch) 3. Flange bearing (2) 6. Hex-head-flange bolt (3/8 x 1–1/4 inches) Figure 2 1. Lift arm 7. Flange nut (5/16 inch) 2.
PAGE 4
Figure 4 1. Slide-lock bracket 4. Flat washer (17/32 inch) 2. Clevis pin—1/2 x 4-1/2 inches (shown before insertion) 5. Drag tongue Figure 5 3. Cotter pin (1/8 x 1 inch) 1. Slide-lock bracket 4. Hairpin cotter 2. Clevis pin (1/2 x 4-1/2 inches) 5. Drag tongue 3. Flat washer (17/32 inch) 2. Insert the remaining clevis pin (1/2 x 4-1/2 inches) through the lowest holes of the slide-lock bracket and secure it with a flat washer (17/32 inch) and a hairpin cotter as shown in Figure 5. 3.
PAGE 5
Assembling and Installing the Drag-Mat Assembly 1. Assemble the mat-bracket frame using 2 crossmember brackets and 2 drag-mat, side brackets together with 2 clevis pins (3/8 x 3/4 inch), 2 cotter pins (15/16 x 3/4 inch), 2 hex-head bolts (3/8 x 1 inch), and 2 flange nuts (3/8 inch) as shown in Figure 7. Figure 9 Figure 7 1. Cotter pin—15/16 x 3/4 inch (2) 5. Crossmember bracket (2) 2. Clevis pin—3/8 x 3/4 inch (2) 6. Drag-mat, bottom bracket (3) 3. Flange nut—3/8 inch (5) 7.
PAGE 6
Operation Using the Drag Mat Important: Do not drive the machine backward when the drag mat is connected and on the ground; otherwise, the wheels in reverse may catch the mat underneath them and damage the mat. Also, the nails from the nail drag may damage the mat. Note: Use caution while operating the machine with the drag mat attached. Drive slowly. For maximum mat life, avoid areas and objects that can snag or interrupt the travel of the mat.
PAGE 7
Notes: 7
PAGE 8
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).