Installation Instructions

ManualsBrandsToro ManualsAttachmentsAuto Drag Mat Kit, Sand Pro/Infield Pro 3040 and 5040 Traction Unit with QAS Nail Drag

FormNo.3417-418RevA

AutoDragMatKit

SandPro

/IneldPro

3040and5040TractionUnitwithQASNail

Drag

ModelNo.08763—SerialNo.400000000andUp

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemical

orchemicalsknowntotheStateof

Californiatocausecancer,birthdefects,

orreproductiveharm.

Introduction

YoumaycontactTorodirectlyatwww.Toro.com

forproductsafetyandoperationtrainingmaterials,

accessoryinformation,helpndingadealer,orto

registeryourproduct.

Wheneveryouneedservice,genuineT oroparts,or

additionalinformation,contactanauthorizedToro

distributororToroCustomerServiceandhavethe

modelandserialnumbersofyourproductready.

Figure1illustratesthelocationofthemodelandserial

numbersontheproduct.Writethenumbersinthe

spaceprovided.

g029872

Figure1

1.Locationofthemodelandserialnumbers

ModelNo.

SerialNo.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3417-418*A

Summary of content (8 pages)

PAGE 1
Form No. 3417-418 Rev A Auto Drag Mat Kit Sand Pro®/Infield Pro® 3040 and 5040 Traction Unit with QAS Nail Drag Model No. 08763—Serial No. 400000000 and Up Installation Instructions WARNING Model No. CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Serial No. Introduction You may contact Toro directly at www.Toro.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 3
Assembling and Installing the Lift-Arm Assembly 1. bearing over the end of the pivot bar, and fully insert the pivot bar to the left arm of the quick-attach coupler to the left side of the lift arm (Figure 3). Attach the wear pad to the lift-arm with 2 hex-head flange bolts (3/8 x 1-1/4 inches) and 2 flange nuts (3/8 inch) as shown in Figure 2. g029874 Figure 3 g227319 Figure 2 1. Lift arm 7. Flange nut (5/16 inch) 2. Hex-head-flange bolt (3/8 x 1-1/4 inches) 8. Lift beam 3. Carriage bolt 9.
PAGE 4
g029877 Figure 4 g029875 1. Slide-lock bracket 4. Flat washer (17/32 inch) 2. Clevis pin—1/2 x 4-1/2 inches (shown before insertion) 5. Drag tongue Figure 5 3. Cotter pin (1/8 x 1 inch) 1. Slide-lock bracket 4. Hairpin cotter 2. Clevis pin (1/2 x 4-1/2 inches) 5. Drag tongue 3. Flat washer (17/32 inch) 2.
PAGE 5
g029876 Figure 6 1. Shackle 4. Spacers 2. Locknut (1/4 inch) 5. Hex-head bolt (1/4 x 2-1/2 inches) 3. Drag tongue 6. Slide-lock bracket Assembling and Installing the Drag-Mat Assembly 1. Secure the front edge of the drag mat and the eyelet ends of the lanyards to the front left and right corners of the mat-bracket frame with 2 hex-head bolts (3/8 x 1-1/4 inches) up from the bottom, 2 zinc spacers, and 2 flange nuts (3/8 inch) as shown in Figure 7. g226896 Figure 7 1. Flange nut (3/8 inch) 3.
PAGE 6
Operation Using the Drag Mat Important: Do not drive the machine backward when the drag mat is connected and on the ground; otherwise, the wheels in reverse may catch the mat underneath them and damage the mat. Also, the nails from the nail drag may damage the mat. Note: Use caution while operating the machine with the drag mat attached. Drive slowly. For maximum mat life, avoid areas and objects that can snag or interrupt the travel of the mat.
PAGE 7
Notes:
PAGE 8
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).