Installation Instructions

ManualsBrandsToro ManualsAttachmentsFront Blade Kit, Sand Pro Bunker Rakes

 2004 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Printed in the USA

Front Blade Kit

Sand Pro



Model No. 08821—Serial No. 30001 and Up

Form No. 3315-579 Rev A

Installation Instructions

Loose Parts

Note: Use the chart below to identify parts used for assembly.

Description

Qty. Use

Blade

Channel

Carriage bolts, 5/16 x 1 inch

Assembling the blade and lift arms

Locknuts, 5/16 inch

Lift arm assembly (left)

Lift arm assembly (right)

Carriage bolts, 5/16 x 1 inch

Locknuts, 5/16 inch

Spacers

Cap screws, 3/8 x 3-3/4 inches

Locknuts, 3/8 inch

Mounting the lift arms to the blade and channel

assembly

Lower handle

Upper handle

Cap screws, 5/16 x 1-3/4 inches

Cap screws, 5/16 x 2-1/4 inches

Cap screws, 5/16 x 2-3/4 inches

Jam nuts, 5/16 inch

Washers, 1/2 inch

Spacers

Mounting the handles to the handle plates

Pivot plates

Cap screws, 5/16 x 1-3/4 inches

Locknuts

Mounting to the foot rest (Sand Pro 2000 only)

Lift arm mounting bracket (left)

Lift arm mounting bracket (right)

Mounting blocks

Cap screws

Mounting lift arm mounting brackets to the

machine (Sand Pro 2000 only)

Lift arm mounting bracket (left)

Lift arm mounting bracket (right)

Cap screws, 1/2 x 1-1/2 inches

Flat washers, 1/2 inch

Mounting lift arm mounting brackets to the

machine (Sand Pro 5000 only)

Summary of content (8 pages)

PAGE 1
Form No. 3315-579 Rev A Front Blade Kit Sand Pro Model No. 08821—Serial No. 30001 and Up Installation Instructions Loose Parts Note: Use the chart below to identify parts used for assembly. Description Qty.
PAGE 2
Description Qty. Shoulder bolts 2 Thrust washers, 5/8 inch 4 Flat washers, 3/8 inch 2 Locknuts, 3/8 inch 2 Mounting pins 2 Thrust washers 4 Klic pins 2 Installation instructions 1 Assembling the Blade and the Lift Arms Use Mounting the center of the lift arms to the machine Mounting the rear of the lift arms to the machine Read before installing and operating the kit 2. Slide the left and right arms into the channel. 3.
PAGE 3
Installing the Lower and Upper Handles Reposition the Front Hydraulic Hoses 1. Install the lower handle on the inside of the handle plate using a cap screw (5/16 x 2-1/4 inch), another cap screw (5/16 x 2-3/4 inch), 4 washers (1/2 inch), 2 spacers, a locknut (5/16 inch), and a jam nut (5/16 inch). Refer to Figure 2. Sand Pro 3020 and 5020 only 1. Position the front wheel so that it is straight ahead. 2. Loosen both of the front wheel motor hydraulic hoses (Fig. 3). Figure 2 1. Lower handle 2.
PAGE 4
2. Assemble the left mounting bracket against the wheel motor mount with the threaded mounting block, 2 cap screws (1/2 x 1-1/2 inches), and lock washers (1/2 inch) (Fig. 4). Figure 5 1. Mounting bracket 2. Wheel motor mount Installing the Pivot Brackets Figure 4 1. Mounting bracket 2. Wheel motor mount Sand Pro 14 and 2000 only 3. Mounting block You must drill 2 holes through the floor boards on each side. 1.
PAGE 5
Figure 7 Figure 9 3. Mount the left and right pivot brackets to the floor boards with 4 cap screws (5/16 x 1-1/2 inch) and 4 locknuts (5/16 inch) (Fig. 8). 1. Pivot arm 2. Floor arm Note: Repeat this set on the opposite side. 3. Connect the rear of the lift arm to the mounting bracket with a mounting pin, 2 thrust washers, and a klic pin (Fig. 10). Figure 8 1. Pivot bracket 2. Left floor board 3. Pivot arm Figure 10 Mounting the Blade and Lift Arm Assembly 1. Lift arm 2. Bracket 3. Pin 1.
PAGE 6
Note: When the spring is properly adjusted, the entire length of the bottom of the blade will be no more than 1/4 inch off the floor. 2. Rotate the spring adjusting nuts (Fig. 11) clockwise to the raise the blade; counterclockwise to lower the blade. Figure 12 1. Handle 2. Spring 3. Transport position 4. Operating position 5. Transport latch 6. Pivot plate pin Figure 11 2. Move the handle to the transport position and pull backward to raise the blade.
PAGE 7
PAGE 8