Installation Instructions

ManualsBrandsToro ManualsAttachmentsDrag Mat Kit, Sand Pro Traction Unit

FormNo.3382-799RevA

DragMatKit

SandPro

TractionUnit

ModelNo.08850

InstallationInstructions

Note:Adrawbaroranishgradermustbeinstalledontherearofthemachineforthedragmattobeinstalled.

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Weight(notincludedwithearlymodelsofthe

kit)

varies

Bolt(1/2x2-1/4inches)

varies

Locknut(1/2inch)

varies

Installtheweights.

Dragmat1

Chain

Screw(5/16x1-1/2inches)

Locknut(5/16inch)

Installthechaintothedragmat.

Cradle(left-hand)

Cradle(right-hand)

Bracket(fordraw-barmountingoption)

Bolt(3/8x1-3/8inches)

varies

Flangenut(3/8inch)

varies

Washer(3/8inch)

varies

Installthecradles.

Shackle

Clevispin

Hairpincotter1

Installthedragmattothemachine.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3382-799*A

Summary of content (8 pages)

PAGE 1
Form No. 3382-799 Rev A Drag Mat Kit Sand Pro® Traction Unit Model No. 08850 Installation Instructions Note: A draw bar or a finish grader must be installed on the rear of the machine for the drag mat to be installed. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
Installing the Weights 3 Always ensure that your machine has the appropriate number of weights. If necessary, install additional weights from the weight kit (sold separately).
PAGE 3
1 3 2 2 1 3 G024799 Figure 6 1. Holes, 10.5 mm (13/32 inch) 4 2. 10.2 cm (4 inches) G024824 Figure 4 With finish grader (Sand Pro 3040 and 5040) 1. Bolt (M12 x 100 mm)—from weight kit 3. Caster fork 2. Weight (8) 4. Locknut (M12)—from weight kit 3. 4.5 cm (1-3/4 inches) 1 Installing the Chain to the Drag Mat 2 5 4 3 G024787 Figure 7 Frame tube Secure 1 end of the chain to the drag mat with a screw (5/16 x 1-1/2 inches) and a locknut (5/16 inch); refer to Figure 5. 1. Frame tube 4.
PAGE 4
1 2. Install the cradles to the finish grader or to the brackets on the draw bar; refer to Figure 9, Figure 10, or Figure 11. 1 2 3 2 9 8 7 6 5 4 G024786 Figure 11 Finish grader—Sand Pro 3040 and 5040 7 6 5 4 3 G024784 Figure 9 Draw bar 1. Finish grader 6. Chain 2. Flange nut, 3/8 inch (4) 7. Shackle 3. Cradle (2) 8. Hairpin cotter 4. Bolt, 3/8 x 1-3/8 inches (4) 9. Clevis pin 5. Washer, 13/32 inch (4) 1. Bolt, 3/8 x 1-3/8 inches (4) 5. Shackle 2. Cradle (2) 6.
PAGE 5
2. Remove the drag mat from the cradles, and place it on the ground. 1 3. Pull the drag mat over the surface that requires grooming. 4. When you have finished or are ready to groom a different area, stow the drag mat in the cradles. 2 6 5 3 Cleaning the Drag Mat 4 Keep the drag mat clean. Excessive soil buildup increases the attachment weight and may affect handling of the machine. G024798 Figure 13 Early model (with finish grader) 1. Cradle 2. Clevis pin 4. Chain 5. Hairpin cotter 3.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8