Form No. 3452-213 Rev A Laser Level Installation Kit Field Pro 6040 Model No. 08865 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 © 2022—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Use Qty. No parts required – Prepare the machine. No parts required – Remove the hood.
Procedure 5 Description Use Qty. 2 1 2 1 2 1 1 2 Bolt (1/4 x 5/8 inch) Locknut (#6) Carriage bolt (#10 x 5/8 inch) Laser controller mount Nut (#10) Grommet Screw (#6 x 1/2 inch) Nut (1/4 inch) Install the laser controller mount. 1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface or move the machine to a machine lift. 2. Engage the parking brake. 3. Raise the mid-mount attachment.
Installing the Receiver Mast Parts needed for this procedure: 2 Bolt (3/8 x 1/2 inch) 4 Flat washer 2 Spacer 3 Locknut (3/8 inch) 2 Curved washer 2 Bushing 3 Knob 1 Receiver mast 1 Locknut (1/2 inch) 1 Thrust washer 1 Mast-support mount 1 Carriage bolt (1/2 x 2-1/2 inches) 2 Carriage bolt (3/8 x 1-1/4 inches) g389485 Figure 3 1. Locknut (3/8 inch) Procedure 1. 2. Mast-support mount Install the mast-support mount to the machine as shown in Figure 3. 3 3.
2. Install the mast to the mast-support mount as shown in Figure 4. 3. Install the upper part of the mast to the machine fork as shown in Figure 4.
3. Remove the existing hoses from the cylinder and the control valve (Figure 5). g389240 Figure 6 g389238 Figure 5 1. Control valve end 1. Existing hoses for the cylinder 4. Remove the 90° elbow fitting from the cooler and at the front of the control valves (Figure 6 and Figure 7). 5 2.
g389239 Figure 7 1. Control valve end 5. Install the 90° elbow fittings, straight fittings, and the bracket to the control manifold (Figure 8). g389237 Figure 8 6 1. 90° elbow fitting (short) 4. Valve bracket 2. 90° elbow fitting (long) 5. Bolt (1/4 x 5/8 inch) 3. Control manifold 6.
6. Install the control manifold and bracket to the machine as shown in Figure 9. 7. Use Figure 10 to identify the hydraulic tubes and the hoses. g389303 Figure 10 g389329 Figure 9 1. Carriage bolt (5/16 x 3/4 inches) 3. Nut (5/16 inch) 2. Manifold with bracket 7 1. Hydraulic hose (90° elbow fitting) 4. Long hydraulic tube (mid-port) 2. Hydraulic hose (48 cm or 19 inches) 5. Short hydraulic tube (mid-port) 3. Hydraulic hose (65 cm or 25-1/2 inches) 6.
. Install the hydraulic hose (90° elbow fitting) to the straight fitting on the manifold, route it back to the hydraulic fluid cooler, and attach the 90° elbow fitting to the hydraulic fluid cooler; refer to Figure 10, Figure 11, and Figure 12. Note: Ensure the hose is routed away from hot surfaces, not rubbing on other parts, and not being pinched. g390674 Figure 12 1. 90° elbow fitting connected to the hydraulic fluid cooler g390663 Figure 11 1.
. Install the short hydraulic tube (mid-port) to the valve control and the 90° elbow fitting (short) on the manifold; refer to Figure 8, Figure 10, and Figure 13. 10. Install the long hydraulic tube (mid-port) to the valve control and the 90° elbow fitting (long) on the manifold; refer to Figure 8, Figure 10, and Figure 14. g389241 g389242 Figure 13 Figure 14 1. Short hydraulic tube (mid-port) 1. Long hydraulic tube (mid-port) 11.
5 Installing the Laser Controller Mount Parts needed for this procedure: 2 Bolt (1/4 x 5/8 inch) 1 Locknut (#6) 2 Carriage bolt (#10 x 5/8 inch) 1 Laser controller mount 2 Nut (#10) 1 Grommet 1 Screw (#6 x 1/2 inch) 2 Nut (1/4 inch) g389243 Figure 15 Procedure 1. Hydraulic tube (no port) 12. Install the hydraulic hoses to the mid-ports in the hydraulic tubes and to the hydraulic cylinder (Figure 10 and Figure 16). g389236 Figure 16 1. Hydraulic hose, 48 cm (19 inches) 2.
g389352 g389353 Figure 17 1. Grommet 2. Locknut (#6) 7. Laser controller mount 8. Carriage bolt (#10 x 5/8 inch) 3. Locknut (#10) 9. Laser controller mount with grommet 4. RAM® mount—provided in the display kit 5. Electrical connector caps—provided in the display kit 10. Nut (1/4 inch) 11. Bolt (1/4 x 5/8 inches) 6.