Operator's Manual

Engine: Briggs & Stratton, Vanguard, 4-cycle, air-cooled,
2-cylinder 11.9 kW (16 hp) @ 3600 rpm, 74.4 cm
3
(29.3
cu. in) displacement. Electric start. Large capacity dual
element air cleaner. Full pressure lubrication 1.55 l (3.5
pint) oil capacity. Solid-state electronic ignition.
Electrical: 12-volt battery, 32-amp-hour. 16-amp alterna-
tor. Ignition switch and interlock switches on control han-
dle, transmission and coring head clutch.
Fuel Capacity: 17 l (4.5 gallons) unleaded gasoline.
Traction Drive: Double-banded V-belt from mechanical
clutch on engine to Peerless Model 2361 transaxle. Two
speeds forward and one reverse. Wheels driven individual-
ly by chains from transaxle.
Ground Speed:
1st Gear Forward: 1.8 km/h @ 3600 rpm (coring)
2nd Gear Forward: 5.3 mph @3600 rpm (transport)
Reverse: 3.1 km/h @ 1800 rpm.
Ground Clearance: 10.2 cm (4 inches).
Tires/Wheels: Two steering tires (front): 13 X 5.00-6, 2
ply, rib tread tubeless.
Two drive tires (rear): 18 X 9.50-8, 4 ply, Rib Terra
tubeless. Drop center demountable rims, greaseable
tapered roller bearings.
Recommended tire pressure for front and back tires is 69
kPa (10 psi).
Frame: Welded steel construction—tricycle.
Service Brake: Disc-type mounted to transaxle.
Controls: Traction clutch, coring head hydraulic lift and
key switch on control console. Throttle and choke on
engine. Transaxle shift lever on frame. Interlock switches
and service brake on steering handle.
Implement Drive: Triple banded V-belt from engine to
coring head.
Coring Unit Construction: Welded steel frame con-
struction with four crankshafts mounted in precision ball
bearings. Crankshafts drive four coring arms/tine heads.
Drive: No. 50 O-ring sealed roller chain from counter-
shaft to coring crankshafts.
Lift: Single hydraulic cylinder powered by a vane type
pump. Control valve actuated by lift control lever.
Tine Heads: 4 individual heads each holding three tines.
Deflector chutes direct cores rearward away from drive
components.
Coring Width: 27 inches
Hole Pattern: 2.25 inches X 2.5 inches
Coring Depth: Up to 3.5 inches.
Tines: Case hardened tubing, hollow tapered design. 5/8"
tines standard. 12 tines required per unit.
Dimensions:
Length: 193 cm (76 inches)
Width: 141 (55.5 inches)
Height: 99.1 cm (39 inches)
Wheelbase: 111.8 cm (44 inches)
Weight: 461.8 kg (1236 pounds)
Optional Accessories:
5/8" Tine Part No. 59-3670
1/2" Tine Part No. 94-3419
3/8" Tine Part No. 59-3690
3/8" Slotted Tine Part No. 94-3418
5/8" Long Wear Tine Part No. 59-9770
5/16" Solid Spiker Tine Part No. 77-5320
*3/4" Tine Part No. 62-4600
*3/4" Slotted Tine Part No. 92–7941
*Tine Block Part No. 62-4610
3/8" Slotted Tine Kit Part No. 94-6814
1/4" Spiker Tine Kit Model 09153
Windrower Model 09150
Coring Head Stand Model 09152
Tire Scrapers Model 09151
*3/4" tines requires 8 optional Tine blocks
7
Specifications