Installation Instructions

ManualsBrandsToro ManualsAttachmentsWheel and Axle Kit, ProCore Processor

FormNo.3358-676RevA

WheelandAxleKit

ProCoreProcessor

ModelNo.09768—SerialNo.280000001andUp

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Carriagebolt(3/8x1inch)

Flangelocknut(3/8inch)

Wheelkit1

Wheel/tireassembly

Lugnut10

Carriagebolt(7/16x1–1/4inch)

Washer8

Locknuts8

Tirescraper2

Bolt(3/8x1inch)

Washer4

Flangenut4

Installthewheelandaxlekit

LooseParts

1.Makesurethetransportwheelsareinthedown

positionandsecuredwiththehitchpinsandlynch

pins.

2.Blockthetransportwheelsorsetthetowvehicle

parkingbrake.

3.Removethe(2)boltsandnutssecuringeachendof

therollerscrapertotheprocessorframe(Figure1).

Also,removethebolt,washerandnutsecuring

thescraperconnectorstraptothecenterofthe

processor.Donotremovethefastenerssecuringthe

rolleradjusterplatestotheprocessorframe.Remove

therollerscraper.Retainthescraper,connector

strapandfastenersforreinstallationifthewheelkit

isremoved.

Figure1

1.Rollerscraper3.Rolleradjusterplate

2.Scraperconnectorstrap

4.Loosentheboltssecuringtherolleradjusterplates

totheframesideplates(Figure1andFigure2).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3358-676 Rev A Wheel and Axle Kit ProCore Processor Model No. 09768—Serial No. 280000001 and Up Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Description Carriage bolt (3/8 x 1 inch) Flange lock nut (3/8 inch) Wheel kit Wheel/tire assembly Lug nut Carriage bolt (7/16 x 1–1/4 inch) Washer Locknuts Tire scraper Bolt (3/8 x 1 inch) Washer Flange nut Use Qty. 1 1 1 2 10 8 8 8 2 4 4 4 Install the wheel and axle kit Loose Parts 1.
PAGE 2
Figure 2 1. Adjuster plate Figure 4 2. Adjuster bolt 1. Wheel/tire assembly 2. Hub 5. Raise the roller until the square holes in the adjuster plates are aligned with the holes in the frame (Figure 3). 3. Lug nut 9. Move the wheel kit into position so the mounting plates are along side the roller adjuster plates. Align the holes in the wheel kit plates with the holes in the frame (Figure 5 and Figure 6). Use the top holes for use in shorter (1 inch) grass. Lower the wheel plates for longer grass.
PAGE 3
Figure 6 11. Loosely mount a tire scraper to each axle bracket with 2 bolts (3/8 x 1 inch), washers and flange nuts. Position the components as shown in Figure 7. Figure 7 1. Tire scraper 12. Position the scraper to attain a clearance of 1/8 inch between the tire and scraper and tighten the fasteners. 13. Check the height and re-adjust as required. Adjust the angle of the processor by adjusting the hitch.
PAGE 4
The Toro General Commercial Products Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial Product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first.