Operator's Manual

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 100-3255



The T

oro Company – 1999

Printed in USA

FORM NO. 3322-791

INSTALLATION

INSTRUCTIONS

Part No. 100–3255

62 Gage Wheel Kit

Loose

Parts

Note: Use the chart below to identify parts for assembly.

DESCRIPTION QTY. USE

Right Bracket

Install Right Front Bracket

Right Rear Gusset

Install Right Rear Bracket

Left Rear Gusset

Install Left Rear Bracket

Gage Wheels

Stud

Spring Disk

Nut

Washer

Flange Nut

Install Gage Wheels

Installing

Right Front Bracket

1. Remove mower from unit. Refer to your

operator manual for instructions.

2. Put a straight edge along the right side of the

unit. Measure over 3–1/16 in. from the straight

edge to locate the position for bracket (Fig. 1).

3. Measure 3–3/8 in. down from the top of the deck

to the center of the top hole in bracket (Fig. 2).

4. Hold bracket and mark mounting location.

5. Remove paint from areas that will be welded

(Fig. 1 and 2).

6. Weld bracket to the mower deck. Weld at a 3

angle (Fig. 1 and 2).

Note: When brackets are placed against deck

they will be at approximately a 3

degree angle. When deck is mounted to

unit it will become aligned with unit.

7. Repaint the area that was welded.

Summary of content (4 pages)

PAGE 1
FORM NO. 3322-791 62 Gage Wheel Kit INSTALLATION INSTRUCTIONS Part No. 100–3255 Loose Parts Note: Use the chart below to identify parts for assembly. DESCRIPTION QTY. Right Bracket 1 Install Right Front Bracket Right Rear Gusset 1 Install Right Rear Bracket Left Rear Gusset 1 Install Left Rear Bracket Gage Wheels 3 Stud 3 Spring Disk 3 Nut 3 Washer 3 Flange Nut 3 Installing Right Front Bracket 1. Remove mower from unit. Refer to your operator manual for instructions. 2.
PAGE 2
Installation Instructions 2 Installing Right Rear Gusset 4 3 1. Using the straight edge along the right side of the unit, measure over 2–13/32 in. from the straight edge to locate the position for bracket (Fig. 3). 2. Measure 1–5/16 in. down from the top of the deck to the center of the top hole in gusset (Fig. 4). 3. Hold wheel bracket and mark mounting location (Fig. 4). 4. Remove paint from areas that will be welded (Fig. 3 and 4). 5. Weld bracket to the mower deck. Weld at a 3 angle (Fig.
PAGE 3
Installation Instructions 4 4 1 3 2 3 1 2 M-4480 Figure 4 1. Rightside of Deck 2. Right Rear Bracket 3. 1–5/16 in. (Top of deck to center of top hole in gusset) 4. Weld Here X M-4475 Figure 5 4. Weld Here X 1. Left Side of Deck 2. Left Rear Gusset 3. 1–5/16 in. (Top of deck to center of top hole in gusset) Installing Left Rear Gusset 1. Put a straight edge along the left side of the unit for a reference. Measure over 3 in. from the straight edge to locate the position for bracket (Fig. 6).
PAGE 4
Installation Instructions Installing Gage Wheels 1. Install stud into gage wheel. Install washer and nut and tighten (Fig. 7). 2. Select hole so gage wheel is positioned to the nearest corresponding height-of-cut desired (Fig. 7). 3. 4. 1 Install flange nut and spring disk while holding stud with wrench (Fig. 7). 6 7 4 3 2 Repeat installation on other gage wheels.