Installation Instructions

ManualsBrandsToro ManualsRiding ProductsWeight Kit, Greensmaster and Sand Pro/Infield Pro Traction Unit

FormNo.3370-543RevD

WeightKit

Greensmaster

andSandPro

/IneldPro

TractionUnit

ModelNo.100-6442

InstallationInstructions

Note:Determinetheleftandrightsidesofthe

machinefromthenormaloperatingposition.

Note:Removethetirefromthecasterforkforease

inholedrillingandinstallationoftheweightkit.

ThisweightkitisnecessaryfortheSand/Ineld

Pro3040and5040TractionUnitstomeetANSI

B71.4-2017andENISO5395:2013standardswhen

thefollowingconditionsaremet:

•TheSandProisequippedwithaSpiker,Rahn

Groomer,FinishGrader,ManualDragMatorNail

Drag

•TheSandProisnotequippedwithafrontliftframe

kit.

TheGreensmaster3100,3120,and31502-Wheel

DriveTractionUnitsequippedwithROPS,Spiker,or

Tri-RollerKitscomplywithANSIB71.4-2017andEN

ISO5395:2013Standardswhentheyareequipped

withthisweightkitand19.5kg(43lb)ofcalcium

chlorideballastaddedtotherearwheel.

TheGreensmaster3250TractionUnitequippedwith

ROPS,thisweightkit,and18kg(40lb)ofcalcium

chlorideballastaddedtotherearwheelandcutting

units,dethatchers,spikers,ortri-rollerkitscomplywith

ANSIB71.4-2017andENISO5395:2013Standards.

Important:Ifapunctureoccursinatirewith

calciumchloride,removethemachinefromthe

turfareaasquicklyaspossible.Toprevent

possibledamagetotheturf,immediatelysoakthe

affectedareawithwater.

PreparingtheMachine

•Parkthemachineonalevelsurface.

•Engagetheparkingbrake(ifapplicable).

•Shutofftheengineandremovethekey(if

applicable).

InstallingtheKitonthe

Greensmaster3100(Model

04356),3120(Model04355),

and3150(Models04357

and04358)

1.Locate,mark,anddrill3holes(13.5mm[0.53

inch])oneachsideoftherearcasterforkas

showninFigure1.

g027765

Figure1

1.127mm(5inches)4.37.4mm(1.47inches)

2.95.3mm(3.75inches)5.74.8mm(2.95inches)

3.37.7mm(1.49inches)

2.Attach3weightstotheleftsideofthecaster

forkusing3bolts(M12x80mm)andlocknuts

(Figure2).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3370-543*D

Summary of content (3 pages)

PAGE 1
Form No. 3370-543 Rev D Weight Kit Greensmaster® and Sand Pro®/Infield Pro® Traction Unit Model No. 100-6442 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Note: Remove the tire from the caster fork for ease in hole drilling and installation of the weight kit. This weight kit is necessary for the Sand/Infield Pro 3040 and 5040 Traction Units to meet ANSI B71.
PAGE 2
3. Attach 5 weights to the right side of the caster fork using 3 bolts (M12 x 110 mm) and locknuts (Figure 2). g016736 Figure 2 1. Weights 3. Bolt (M12 x 110 mm) 2. Bolt (M12 x 80 mm) 4. Locknut (M12) Installing the Kit on the Greensmaster 3250-D (Models 04383 and 04384) 1. g027766 Figure 3 Locate, mark, and drill 3 holes (13.5 mm [0.53 inch]) on each side of the rear caster fork as shown in Figure 3. 1. 127 mm (5 inches) 4. 37.4 mm (1.47 inches) 2. 95.3 mm (3.75 inches) 5. 74.8 mm (2.
PAGE 3
Installing the Kit on the Sand/Infield Pro 3040 (Model 08703) 1. Installing the Kit on the Sand/Infield Pro 5040 (Model 08705) 1. Locate, mark, and drill 2 holes (13.5 mm [0.53 inch]) on each side of the front caster fork as shown in Figure 5. Locate, mark, and drill a hole (13.5 mm [0.53 inch]) on each side of the front caster fork as shown in Figure 7. g027767 Figure 5 1. 13.5 mm (0.53 inch) 4. 31.7 mm (1.25 inches) 2. 127 mm (5 inches) 5. 37.4 mm (1.47 inches) g027768 Figure 7 3. 112.5 mm (4.