Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 105-1502

Printed in the USA

 2001 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Adapter Kit

2001 and Earlier Snow/Dozer Blade to a 2002 and Later GT

Classic Garden Tractor

Part No. 105–1502

Form No. 3327–136

Installation Instructions

Loose Parts

Note: Use the chart below to identify parts for assembly .

DESCRIPTION QTY. USE

Lever 1

Installing the Lever onto a 2000 and 2001

Snow/Dozer Blade

Lever

R–clamp

Bolt, 1/4 x 1 in.

Locknut, 1/4 in.

Cotter pin

Cable bracket

Installing the Lever onto a 1999 and Earlier

Snow/Dozer Blade

Cable 1 Installing the New Cable

Installing the Lever onto a 2000

and 2001 Snow/Dozer Blade

Note: The following instructions are for the 2000 and

2001 models only.

Installing the New Lever

1. Disengage the power take off (PTO), set the parking

brake and turn the ignition key to of f. Remove the key.

2. Remove the existing cable from the lever (Fig. 1).

3. Remove the index lever (Fig. 1). Save all the

hardware.

4. Remove the control rod from the lever (Fig. 1).

5. Remove the existing lever from the snow/dozer blade.

Save all the hardware.

6. Install the index lever to the new lever .

7. Attach the new lever to the pivot support using the

pivot bolt (1/2 x 1 in.). Screw the bolt into the pivot

support until the handle is snug and then back it of f

slightly to let the handle pivot freely (Fig. 1).

Summary of content (4 pages)

PAGE 1
Form No. 3327–136 Adapter Kit 2001 and Earlier Snow/Dozer Blade to a 2002 and Later GT Classic Garden Tractor Part No. 105–1502 Installation Instructions Loose Parts Note: Use the chart below to identify parts for assembly . DESCRIPTION QTY. Lever 1 Lever 1 R–clamp 3 Bolt, 1/4 x 1 in. 3 Locknut, 1/4 in.
PAGE 2
8. Secure the bolt with a jam nut (Fig. 1). 1 4 1 6 7 8 5 6 3 7 6 2 8 7 6 4 5 7 m-5695 Figure 2 8 1. 2. 3. 4. 3 Lever Index plate Cable Control rod 5. 6. 7. 8. Hair pin cotter Nut Bolt Index lever 10 6. Remove the index plate from the machine (Fig. 3). 7. Remove the lower index rod from the machine (Fig. 3). 9 1 5 2 3 2 m–5576 Figure 1 1. 2. 3. 4. 5. Lever Control rod Large hairpin cotter Index lever Z-fitting 6. 7. 8. 9. 10. Bolt, 1/4 x 1 in. Cable clip Locknut, 1/4 in.
PAGE 3
12. Remove the excess material between the two holes (Fig. 4). 1 4 5 6 6 1 7 5 8 6 7 2 4 3 8 1 3 10 7 m–5697 9 Figure 4 1. 2. 3. 4. Cross support Center of cross support 21/64 in. hole 5/8 in. hole 5. Key hole 6. Right side of frame 7. 5/8 in. 2 m–5576 Figure 5 1. 2. 3. 4. 5. 13. Install cable bracket onto pin with a cotter pin (Fig. 5). 14. Attach the new lever to the pivot support using the pivot bolt (1/2 x 1 in.).
PAGE 4
3. Insert the control rod through the handle end and secure it with a lar ge hairpin cotter (Fig. 6). 1 4. Connect the Z-fitting on the end of the cable to the release lever (Fig. 6). 1 4 5 6 6 5 7 7 3 2 8 6 m05040 & 5041 7 4 8 7 6 Figure 7 1. 2. 3. 4. 3 10 Rear view Front view Cable jacket Cable 7. Tighten the jam nuts (Fig. 7). 9 8. Insert the balled end of the cable into the cable bracket (Fig. 8).