Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 105-1621

The Toro Company – 2002

Printed in USA

FORM NO. 3326–318 Rev A

INSTALLATION

INSTRUCTIONS

Part No. 105–1621

Z–Stand



Kit

Z–Master 100 Series

Safety and Instruction Decals

Safety decals and instructions are easily visible to the operator and are located near any

area of potential danger. Replace any decal that is damaged or lost.

Part No. 104–7759

Loose Parts

Note: Use the chart below to identify parts for assembly.

DESCRIPTION QTY. USE

Z–Stand hub

Bracket latch

Bolt, 3/8 x 1–1/2 in.

Lock nut, 3/8 in.

Assemble 100 Series Z–Stand hub

Z–Stand hub

Bolt, 3/8 x 3–1/2 in.

Lock nut, 3/8 in.

Hair Pin cotter

Clevis pin, 3 in.

Clevis pin, 2–5/8 in.

Install 100 Series Z–Stand hub

Summary of content (8 pages)

PAGE 1
FORM NO. 3326–318 Rev A Z–Stand Kit Z–Master 100 Series Part No. 105–1621 INSTALLATION INSTRUCTIONS Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. Part No. 104–7759 Loose Parts Note: Use the chart below to identify parts for assembly. DESCRIPTION QTY. Z–Stand hub 1 Bracket latch 1 Bolt, 3/8 x 1–1/2 in. 1 Lock nut, 3/8 in.
PAGE 2
Installation Instructions DESCRIPTION QTY. Z–Stand foot 1 Z–Stand tube 1 Thrust washers 2 Lynch pin 1 Hair pin cotter 2 Clevis pin 2 Z–Stand bracket 1 Bolt, 5/16 x 2–3/4 in. 1 Lock Nut, 5/16 in. 1 Bolt, 1/4 x 3/4 in. 1 Lock Nut, 1/4 in. 1 Lanyard 1 USE Install 100 Series Z–Stand Install 100 Z–Stand bracket The following instructions are for installing the Z–Stand on a 100 Series Z–Master. 2 4 Assemble 100 Series Z–Stand Hub 1 1.
PAGE 3
Installation Instructions 2 4 4 1 4. 3 Insert pivot pin into the Z–Stand hub as shown in figure 4. Note: 5. When inserting the pivot pin, make sure the position of slot in tube is as shown in figure 3. Place a thrust washer onto the pivot pin and secure with a lynch pin (Fig. 4). m–5357 Figure 2 1. Right front frame 2. Z–Stand hub assembly 3. Bolt, 3/8 x 3–1/2 in. 4. Lock Nut, 3/8 in. 5 3 4 Install 100 Series Z–Stand 1. 4 2 Place the foot part of stand into the Z–Stand tube.
PAGE 4
Installation Instructions 8 7 4 4 5 2 5 1 2 6 1 3 3 m–5357 Figure 5 1. 2. 3. 4. Left front caster housing Z–Stand bracket Bolt, 5/16 x 3–1/4 in. Lock Nut, 5/16 in. 5. 6. 7. 8. m–5375 Figure 6 Lock Nut, 1/4 in. Bolt, 1/4 x 3/4 in. Lanyard Bracket Pin 1. Z–Stand 2. Latch 3. Bracket 4. Bracket Pin 5. Bottom of slot 3. Raise latch. Swing stand foot out front and slide stand toward machine, into the bottom of slot (Fig. 6 and 8).
PAGE 5
Installation Instructions 3 4 1 2 2 3 1 m–5374 Figure 8 1. Z–Stand (Positioned in slot) 2. Crack in side walk or turf 3. Latch resting on pivot tab m–5373 Figure 9 1. Z–Stand 2. Latch 3. Locked position 4. Unlocked position 8. Drive onto stand. Stop when latch drops over tab into locked position (Fig. 9). Once onto stand, engage parking brake. Shut off engine. 9. Chock or block the drive wheels.
PAGE 6
Installation Instructions 6
PAGE 7
Installation Instructions 7
PAGE 8
Installation Instructions 8