Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 105-3180

Printed in the USA

 2002 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

36 Recycler Kit

Proline Mid–Size Floating Deck Mowers

Part No. 105–3180

Form No. 3328-137

Installation Instructions

Loose Parts

Note: Use the chart below to identify parts for assembly.

DESCRIPTION QTY. USE

Baffle

Bolt, 5/16 x 1 inch

Bolt, 5/16 x 2–3/4 inch

Lock nut, 5/16 inch

Installing the baffle

Kicker

Bolt 5/16 x 1 inch

Lock nut, 5/16 inch

Installing the kickers

Recycler



blade 2 Installing the blades

Preparing the Mower

1. Remove the mower and belt. See the Operator’s Manual

for instructions.

2. Thoroughly clean the mower. All debris must be

removed to ensure kickers and baffle will fit properly

against mower.

3. Repair all bent or damaged areas of mower and replace

any missing parts.

4. Tip the mower upside down and block up ends to ease

installation of recycler components.

Open holes in the mower exposes you and others to

thrown debris. Debris thrown out of holes in the

mower can cause injury.

• Never operate mower without hardware

mounted in all holes in mower.

• Install hardware in mounting holes when

mulching baffle is removed.

Warning

Summary of content (4 pages)

PAGE 1
Form No. 3328-137 36 Recycler Kit Proline Mid–Size Floating Deck Mowers Part No. 105–3180 Installation Instructions Loose Parts Note: Use the chart below to identify parts for assembly. DESCRIPTION QTY. Baffle 1 Bolt, 5/16 x 1 inch 2 Bolt, 5/16 x 2–3/4 inch 2 Lock nut, 5/16 inch 4 Kicker 2 Bolt 5/16 x 1 inch 4 Lock nut, 5/16 inch 4 Recycler blade 2 USE Installing the baffle Installing the kickers Installing the blades Preparing the Mower 1. Remove the mower and belt.
PAGE 2
Installing the Baffle 3 6 Important Make sure the bolt heads are installed on the inside of the cutting chamber. 8 6 5 5 1 1. Place the baffle inside the front of the cutting chamber (Fig. 2). 2. Position the baffle so the outside ends are tight against the cutting chamber and there is equal distance between the baffle radius’ and spindles (Fig. 3). 7 Note: Do not drill a hole in the center. See Figures 1 and 2. 7 3. Using the baffle as a template, drill four holes (11/32 inch dia.
PAGE 3
Installing the Kickers 2 . Important Make sure the bolt heads are installed on the inside of the cutting chamber. 1 1. Measure from the spindle center lines, and locate kickers as shown in Figure 3. 5 2. Holding kickers tight against the cutting chamber, mark and drill a hole for each kicker (11/32 inch dia.) (Fig. 3). 4 5 5 5 4 3 m–6248 Figure 4 1. Kicker 2. Bolt, 5/16 x 1 inch 3. Lock nut, 5/16 6 3 m–6249 3 3 4 2 1 Figure 3 1. 4–1/4 inch (108 mm) 2. 3-1/2 inch (89 mm) 3.
PAGE 4
Installing the Recycler Blades Removing Baffles for Side Discharge Cutting 1. Hold the blade end using a rag or thickly-padded glove. Remove the blade bolt, blade stiffener and blade from the spindle shaft (Fig. 5). Note: Keep the rear 3 kickers attached to the mower. 1. Thoroughly clean the mower. 2. Install the blade onto the spindle shaft (Fig. 5). 2. Remove the mower to ease removal of kit.