Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 106-5869

Printed in the USA

 2002 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Bagger Arm Kit for Use with ROPS

100 Series Z Master Mowers

200 Series Z Master Mowers

Part No. 106–5869

Part No. 106–5890

Form No. 3328–214

Installation Instructions

Loose Parts

Description Qty. Use

Bagger arm

Cable tie

Grip

Cotter pin

Cable—100 Series Baggers Only

Installing the bagger lever for 100 Series and

200 Series baggers

Bolt, 5/16 x 1–1/4 inch

Washer, 11/32 inch

Installing the washers for a 100 Series ROPS

Install this kit when both a bagger and Roll Over Protection

System (ROPS) are used together.

Removing the Existing Bagger

Arm

1. Remove the shoulder bolt and cable from the bagger

arm (Fig. 1). Keep the shoulder bolt for use with new

bagger arm.

Note: Steps 2 and 3 are for 100 Series baggers only.

2. For 100 Series baggers only, remove the nut and pulley

from the bagger and remove the cable (Fig. 1). Save the

pulley and all hardware.

3. For 100 Series baggers only, remove the cable from the

bagger door hinge (Fig. 1). Save all hardware.

4. Loosen the setscrew holding the latch lever.

5. Cut the cable tie (Fig. 1).

6. Remove the grip from the bagger arm (Fig. 1).

m–6136

Figure 1

1. Bagger arm

2. Cable

3. Shoulder bolt

4. Pulley and nut

5. Bagger door hinge

6. Cable tie

7. Latch lever

8. Grip

Summary of content (8 pages)

PAGE 1
Form No. 3328–214 Bagger Arm Kit for Use with ROPS 100 Series Z Master Mowers 200 Series Z Master Mowers Part No. 106–5869 Part No. 106–5890 Installation Instructions Loose Parts Description Qty.
PAGE 2
7. Remove the cotter pin and washer from the bagger arm (Fig. 2). Save the washer. 3 8. Slide the existing bagger arm out from the bagger and save the washer (Fig. 2). 2 9. Remove the latch lever off of the bagger arm (Fig. 1). 1 4 3 5 m–6207 Figure 3 1. Bagger arm 2. Latch lever 3. Grip 4 2 3. For 100 Series baggers, position the bagger arm inside the right rear corner of the ROPS and under the cross member (Fig. 4). 4 1 m–6206 4.
PAGE 3
2 4 4 3 2 1 5 5 3 5 1 m–6138 m–6137 Figure 4 1. Bagger arm—100 Series (Install inside ROPS) 2. Cotter pin 3. ROPS—100 Series (Rollover Protection System) Figure 5 4. Bagger 5. Existing washer 1. Bagger arm—200 Series (Install outside ROPS) 2. Cotter pin 3. ROPS—200 Series (Rollover Protection System) 4. Bagger 5. Existing washer Note: For 100 Series baggers, use the new cable included in the kit. 200 Series baggers use the existing cable. 7.
PAGE 4
5 2 4 7 8 5 6 3 7 7 4 2 6 1 4 3 9 1 1 m–6208 m–6212 Figure 6 1. 2. 3. 4. 5. Bagger arm Cable Existing shoulder bolt Pulley and nut Bagger door hinge 6. 7. 8. 9. Figure 7 Cable tie Latch lever Grip ROPS (Rollover Protection System) 1. Bagger arm 2. Latch lever position—100 Series 3. Latch lever position—200 Series 4. 5. 6. 7. Latch lever cable 5 inches—100 Series 6 inches—200 Series Grip Adjusting the Latch Lever Adjusting the Bagger Arm 1.
PAGE 5
3 1 4 1 6 2 4 1 5 2 3 5 5 6 m–6211 3 Figure 9 m–6209 1. Existing flange nut, 5/16 inch 2. Bolt, 5/16 x 1–1/4 inch 3. Flat washer, 5/16 inch 4. Front floorpan Figure 8 1. Bagger arm 2. Stop bracket 3. Stop bolt 2 4. Bagger cable 5. Nut Installing the Washers for a 100 Series ROPS Install washers when a 100 Series bagger and ROPS are used at the same time. 1. Remove the 4 bolts, washers and flange nuts that hold the front floorpan and support plate to the front frame (Fig. 9).
PAGE 6
PAGE 7
PAGE 8