Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 107-1891

FormNo.3365-958RevA

DeluxeSuspensionSeatKit

Z100,Z200,Z400andZ500SeriesZMaster

Mowers

ModelNo.78530or107–1891

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Removetheseat.

Bolt(7/16x1inch)

2Installtheseatbelt.

Deluxesuspensionseat1

Spacer(2holesforZ200/Z500Series)

Spacer(3holesforZ100/Z400Series)

Installtheseat.

Wireharness1

Plasticties

Installthewireharness.

Nopartsrequired

–

Testthesafetyinterlocksystem.

Decal1Installthedecal.

RemovingtheSeat

NoPartsRequired

Procedure

1.Unlatchtheseatandtiptheseatforward.

2.Removethenutsholdingtheseattothemounting

frame(

Figure1).Retainthenuts.

3.Removetheseatfromtheframeandsetitaside.

Figure1

1.Seat

3.Nut

2.Seatframe

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3365-958 Rev A Deluxe Suspension Seat Kit Z100, Z200, Z400 and Z500 Series Z Master® Mowers Model No. 78530 or 107–1891 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Use Qty. No parts required – Remove the seat. Bolt (7/16 x 1 inch) 2 Install the seat belt.
PAGE 2
Installing the Seat Belt Parts needed for this procedure: 2 Bolt (7/16 x 1 inch) Figure 2 1. Bolt 2. Seat belt retractor 3. Nut Procedure WARNING 4. Seat belt receiver 5. Seat 2. Install the seat belt retractor and receiver to the deluxe seat using the 2 bolts (7/16 x 1 inch) (Figure 5 &Figure 3). Serious injury or death can happen when the seat belt is used without a roll bar installed. Do not install the seat belt without a roll bar installed.
PAGE 3
Installing the Seat Parts needed for this procedure: 1 Deluxe suspension seat 2 Spacer (2 holes for Z200/Z500 Series) 2 Spacer (3 holes for Z100/Z400 Series) Procedure Figure 5 1. Place the spacers on the seat mounting frame with the bent ends facing up. The slot in the spacer is installed to the back of the seat (Figure 4). 1. Seat track studs 2. Seat 3. Spacer (2 holes for Z200 or Z500 series shown) 4.
PAGE 4
WARNING If the safety interlock switches are both connected the machine could operate unexpectedly causing personal injury. 3 • Ensure the old switch is removed from the machine. 1 2 • Ensure the new harness is connected to the new seat switch in the seat. • Check the operation of the interlock switches daily and replace any damaged switches before operating the machine. 3.
PAGE 5
Testing the Safety Interlock System No Parts Required Procedure 9 WARNING If safety interlock switches are disconnected or damaged the machine could operate unexpectedly causing personal injury. • Do not tamper with the interlock switches. • Check the operation of the interlock switches daily and replace any damaged switches before operating the machine. 11 12 13 14 15 The safety interlock system is designed to prevent the engine from starting unless: • The parking brake is engaged.
PAGE 6
Operation levers to neutral lock position. Now start the engine. While the engine is running, center either motion control and move (forward or reverse); the engine should stop. Repeat for other motion control. Adjusting the Suspension Seat 5. Sitting on the seat, disengage the parking brake, move the PTO switch to off and move the motion control levers to neutral lock position. Try starting the engine; the engine should not crank.
PAGE 7
Notes: 7
PAGE 8