Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 107-8599

W 2004 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Printed in the USA

Original Instructions (EN)

Z Stand

Kit

400 Series Z Masters

Part No. 107–8599

Form No. 3352-476 Rev B

Installation Instructions

Safety and Instruction Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger. Replace any decal that is damaged or lost.

104-7759

Loose Parts

Note: Use the chart below to identify parts for assembly.

DESCRIPTION QTY. USE

Z Stand hub

Bracket latch

Bolt, 3/8 x 1–1/2 inch

Lock nut, 3/8 inch

Assembling the Z Stand hub

Z Stand hub

Bolt, 3/8 x 3–1/2 inch

Lock nut, 3/8 inch

Hair Pin cotter

Clevis pin, 3 inch

Installing the Z Stand hub

Summary of content (8 pages)

PAGE 1
Z StandR Form No. 3352-476 Rev B Kit 400 Series Z Masters Part No. 107–8599 Installation Instructions Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 104-7759 Loose Parts Note: Use the chart below to identify parts for assembly. DESCRIPTION QTY.
PAGE 2
DESCRIPTION QTY. Z Stand foot 1 Z Stand tube 1 Thrust washers 2 Lynch pin 1 Hair pin cotter 2 Clevis pin 2 Z Stand cradle bracket 1 Bolt, 3/8 x 3–1/4 inch 1 Lock Nut, 3/8 inch 1 Bolt, 1/4 x 3/4 inch 1 Lock Nut, 1/4 inch 1 Lanyard 1 USE Installing the Z Stand Installing the Z Stand cradle bracket The following instructions are for installing the Z Stand on a 400 Series Z Master. 2 Assembling the Z Stand Hub 3 1 1.
PAGE 3
Installing the Z Stand Installing the Z Stand Cradle Bracket 1. Place the foot part of stand into the Z Stand tube. Align holes and secure with a clevis pin (2–5/8 inch) and hair pin cotter (Fig. 3). 1. Place the Z Stand cradle bracket onto the left front frame as shown in Figure 5. 2. Install the Z Stand assembly to the pivot pin with a clevis pin (3 inch) and hair pin cotter (Fig. 3). 2. Install the Z Stand cradle bracket with a bolt (3/8 x 3–1/4 inch) and lock nut (3/8 inch) (Fig. 5).
PAGE 4
Using the Z Stand 2 The Z Stand is used for raising the front end of the machine. This allows for cleaning of the deck and removal of the blades. Warning 1 Unit could fall onto someone and cause serious injury or death. 3 • Use extreme caution when operating unit on Z Stand. • Use only for cleaning deck and removing blades. • Do not keep unit on Z Stand for extended periods of time. • Always shut engine off and set parking brake before performing any maintenance to deck. m–5380 Figure 7 1.
PAGE 5
Driving off the Z Stand 1. Raise latch to unlocked position (Fig. 9). 2. Start engine and place at half throttle. Disengage parking brake. 3. Slowly drive backwards off of stand. 4. Remove the cotter hair pins and stand pins (Fig. 7). 5. Push in the inner part of stand and insert stand pins and cotter hair pins (Fig. 7). 6. Return stand to its rest position (Fig. 6). 7. Insert bracket pin into Z Stand cradle bracket (Fig. 6). 4 2 3 1 m–7861 Figure 9 1. Z Stand 2. Latch 3. Locked position 4.
PAGE 6
PAGE 7
PAGE 8