Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 108-4101

Form No. 3353-646 Rev A

Bagger Latch Kit

For Z Master Twin and Triple Baggers

Model No. 108–4101

Installation Instructions

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

No parts required

–

Removing the existing latch

No parts required

–

Removing the front part of the latch

guard

Handle

Rod hook

Grip

Locknut (3/8 inch)

Jam nut (3/8 inch)

Assembling the new latch

No parts required

–

Drilling hole for new latch

Bolt (5/16 x 1 inch)

Bolt (5/16 x 1-7/8 inch

Locknut (5/16 inch)

Latch assembly

Pivot plate

Spacer

Installing the new latch

No parts required

–

Adjusting the new latch

Step

Removing the Existing Latch

No Parts Required

Procedure

1. Diseng ag e the PTO , set the parking brak e , and

c hoc k or bloc k the dri v e wheels .

2. T ur n off the engine , remo v e the k ey , and w ait

for all mo ving par ts to stop before lea ving the

operating position.

3. Unlatc h the blo w er and remo v e it from the

mac hine .

4. R emo v e the spring from the latc h and the

blo w er ( Figure 1 ).

5. R emo v e the n uts and bolt holding the existing

latc h to the blo w er and remo v e it. Discard

the latc h, spring and hardw are ( Figure 1 and

Figure 2 ).

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Summary of content (8 pages)

PAGE 1
Form No. 3353-646 Rev A Bagger Latch Kit For Z Master Twin and Triple Baggers Model No. 108–4101 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Step 1 2 Description Use Qty.
PAGE 2
Step 2 Removing the Front Part of the Latch Guard No Parts Required Procedure Cut off part of the latch guard as shown inFigure 3. Figure 1 1. Blower 2. Existing latch 3. Spring 4. 5. 6. Washer Bolt Nut Figure 3 1. Latch guard 2. Remove the shaded area Figure 2 1. Blower 2. Nut 3. Existing latch 2 3.
PAGE 3
Step 3 Assembling the New Latch Parts needed for this step: 1 1 1 1 1 Handle Rod hook Grip Locknut (3/8 inch) Jam nut (3/8 inch) Procedure 1. Install the jam nut (3/8 inch) all the way onto the threaded rod hook end (Figure 4 ). 2. Install the rod hook through the block in the middle of the handle and secure it with a locknut (3/8 inch) until there is one thread showing on the end of the rod hook (Figure 4 ). Figure 4 1. 2. Handle Jamnut (3/8 inch) 3. 4.
PAGE 4
Figure 6 1. Locknut (5/16 inch) 2. Blower 3. Latch 3. 4. Spacer Pivot plate Bolt (5/16 x 1–7/8 inch) 2. Install the latch assembly and pivot plate using the previously drilled hole in the blower with a bolt (5/16 x 1 inch) and locknut (5/16 inch) (Figure 7). Figure 5 1. 11/32 inch hole to drill 2. 5/8 inch 4. 5. 6.
PAGE 5
Step 4. The blower latch must engage the front peg properly (Figure 9). If it does not, proceed to item 5 of this procedure and lengthen the latch. 6 Adjusting the Latch No Parts Required Procedure Adjust the blower latch when it is does not engage the front peg correctly. A 9/16 inch thin wall deep socket is recommended for this procedure. 1. Check that the bagger belt is properly installed and routed correctly. Refer to the Operator’s Maual. 2.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8