Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 110-0351

W 2005 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Printed in the USA

Original Instructions (Language abbreviation)

DFS Bagger Adapter Kit

for Mounting 2004 and Before Baggers on 2005 and After

Z500 Series Z Masters

Part No. 110–0351

Form No. 3353–606 Rev B

Installation Instructions

Note: Use the existing hardware that came with the bagger to install the bagger mounting bracket in Step 3.

Setup

Note: Determine the left and right sides of the machine from the normal operating position.

Loose Parts

Note: Use the chart below to verify all parts have been shipped.

Step

Description Qty. Use

Side bracket—right

Side bracket—left

Bolt, 3/8 x 1–1/2 inch

Flange Nut, 3/8 inch

Stiffener bracket

Curved washer

Installing bagger mounting brackets

onto the machine

No parts needed Tightening all mounting bolts

Step

Parts needed for this step:

• 1 Bagger mounting bracket

• 1 Side bracket—right

• 1 Side bracket—left

• 4 Long frame spacer—only two are needed for air

cooled machines

• 2 Short frame spacer

• 12 Bolt, 3/8 x 1–1/2 inch

• 4 Bolt, 3/8 x 1–1/4 inch

• 26 Flange Nut, 3/8 inch

• 2 Stiffener bracket

• 8 Bolts, 3/8 x 3/4 inch

• 8 Curved washer

If you have a liquid cooled machine, go to page 3 for

Installing the Bagger Mounting Bracket onto a Liquid

Cooled Machine.

If you have an air cooled machine, use the following

instructions for Installing the Bagger Mounting Bracket

onto an Air Cooled Machine.

Installing the Bagger Mounting

Bracket onto an Air Cooled

Machine

Important Do not tighten any bolts until both side

brackets and bagger mounting bracket are fit loose on the

machine.

Refer to Tightening the Mounting Bolts, on page 4, for the

correct procedure to tighten the bolts.

Summary of content (4 pages)

PAGE 1
Form No. 3353–606 Rev B DFS Bagger Adapter Kit for Mounting 2004 and Before Baggers on 2005 and After Z500 Series Z Masters Part No. 110–0351 Installation Instructions Note: Use the existing hardware that came with the bagger to install the bagger mounting bracket in Step 3. Setup Note: Determine the left and right sides of the machine from the normal operating position. Loose Parts Note: Use the chart below to verify all parts have been shipped. Step 1 2 Step Description Qty.
PAGE 2
Installing the Bagger Mounting Bracket to the Side Brackets (Air Cooled) Installing the Side Brackets to an Air Cooled Machine Important When installing the bagger bracket for an air cooled machine, use only 2 long frame spacers; 1 per each side (Fig. 1). Important Do not tighten any bolts until both side brackets and bagger mounting bracket are fit loose on the machine. 1. Install the side brackets to the bagger mounting bracket (Fig. 1). Important Install one side at a time. 1.
PAGE 3
. In the bottom hole, install a bolt (3/8 x 1–1/4 inch) and a flange nut (3/8 in.) (Fig. 4). 2. In the top two holes, install 2 bolts (3/8 x 1–3/4 inch), 2 flange nuts (3/8 in.) and the air cooled frame spacer (Fig. 3). 4. Install a bracket stiffener to the side bracket and bagger mounting bracket. Use 4 bolts (3/8 x 3/4 inch) and 4 flange nuts (3/8 in.) (Fig. 4). 3. In the bottom two holes, install 2 bolts (3/8 x 1–1/4 inch) and 2 flange nuts (3/8 in.) (Fig. 3). 5 5.
PAGE 4
Step 4 1 2 No parts needed for this step. 5 2 Tightening all Mounting Bolts 3 The following steps are the correct sequence to tighten the side brackets and the bagger mounting bracket. 3 2 m–8044 All 3/8 inch mounting bolts need to be torqued to 35 ft–lb (48 Nwm). Figure 5 1. Side bracket 2. Curved washer, 3/8 inch 3. Bolt, 3/8 x 1–1/2 inch 4. Flange nut, 3/8 inch 5. ROPS 1. Tighten the bagger mounting bracket to the rear frame first (Figures 3 or 6). 2.