Installation Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 110-5761

Form No. 3357-679 Rev A

Mower Deck Lift Assist Kit

For Z500 Series Z Master® with 7-Guage Mower Deck

Model No. 110–5761

Installation Instructions

Installation

Note: Deter mine the left and right sides of the mac hine from the nor mal operating position.

Step

Removing the Existing Lift

Shaft

No Parts Required

Procedure

1. Diseng ag e the PTO and set the parking brak e .

2. Stop the engine , remo v e the k ey , and w ait for

all mo ving par ts to stop before lea ving the

operating position.

3. Raise the mo w er dec k to the transpor t position,

the highest position.

4. Place bloc ks under the edg e of the mo w er dec k

to release tension on the lift c hains when the

mo w er dec k is lo w ered.

5. Lo w er the mo w er dec k onto the bloc ks to

release tension on the lift c hains .

6. R emo v e the n ut and bolt securing the mo w er

lift c hain to the right front lift shaft ( Figure 1 ).

R etain the n ut and bolt.

7. R emo v e the E-ring and the w asher securing

the front of the lift spring assembly to the lift

shaft and remo v e the lift spring assembly from

the lift shaft ( Figure 1 ). R etain the E-ring and

w asher .

8. R emo v e the E-ring and w asher securing the lift

shaft to the frame and remo v e the lift shaft.

R etain the E-ring and w asher .

Step

Installing the Lift Assist

Lever

Parts needed for this step:

Lift assist lever

Washer

Snap ring

Procedure

1. Slide the new lift assist lev er into the frame

( Figure 1 ).

2. Secure the lift assist lev er with the new w asher

and snap ring ( Figure 1 ).

3. Install the front of the lift spring assembly to

the lift assist lev er with the E-ring and the

w asher ( Figure 1 ).

4. Secure the lift c hain to the lift assist lev er with

the n ut and bolt previously remo v ed ( Figure 1 ).

5. Grease the lift assist lev er under the frame .

6. Raise the mo w er dec k off the bloc ks .

7. Chec k and ensure all four mo w er dec k lift

c hains ha v e tension. If not, loosen the n uts on

eac h side of the swi v el and shor ten or lengthen

the lift spring assemblies as required.

If fur ther adjustment is required, refer the

mo w er dec k lev eling section of the Operator’ s

Man ual .

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Summary of content (2 pages)

PAGE 1
Mower Deck Lift Assist Kit Form No. 3357-679 Rev A For Z500 Series Z Master® with 7-Guage Mower Deck Model No. 110–5761 Installation Instructions Installation Note: Determine the left and right sides of the machine from the normal operating position. Step Step 1 2 Removing the Existing Lift Shaft Installing the Lift Assist Lever No Parts Required Parts needed for this step: Procedure 1. Disengage the PTO and set the parking brake. 2.
PAGE 2
Figure 1 1. 2. 3. 4. 5. Lift assist lever Washer Snap ring E-ring Washer 6. 7. 8. 9. 10. Nut Mower lift chain Bolt Lift spring assembly Height-of-cut handle Operation Using the Lift Assist Lever The lift assist lever is used along with the height-of-cut lever for raising the mower deck. This allows for easier raising of the mower deck. 1. Place your foot onto the lift assist lever. 2. Press on the lift assist lever while pulling up on the height-of-cut lever.