Installation Instructions

ManualsBrandsToro ManualsAttachmentsLift Alarm Kit, Pro Sweep 5200 Turf Sweeper

W 2006 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Printed in the USA

Lift Alarm Kit

Pro Sweep 5200 Turf Sweeper

Part No. 110–7994

Form No. 3355–178 Rev A

Installation Instructions

Loose Parts

Note: Use this chart as a checklist to ensure that all parts have been received. Without these parts, total setup cannot be

completed.

Description

Qty. Use

Proximity switch

Block spacer

Switch plate

Screw, #10 x 1–1/2 inch

Screw, #10 x 1–3/4 inch

Flat washer, .216 x .500 inch

Nut, #10

Switch arm assembly

Torsion spring

Cam spacer

Washer

Screw, 5/16 x 2–3/4 inch

Yoke spacer

Flat washer, .375 x .734 inch

Screw, 5/16 x 1–1/4 inch

Indicator light

Clamp

Audio alarm 1

Control box wire harness 1

Trailer wire harness 1

Cable tie 18

Control box cover 1

Decal, control box 1

Decal, warning 1

Installation Instructions

Parts Catalog

Operator Manual Addendum 1

Keep with Pro Sweep 5200 Turf Sweeper

Operator Manual for reference

Summary of content (8 pages)

PAGE 1
Form No. 3355–178 Rev A Lift Alarm Kit Pro Sweep 5200 Turf Sweeper Part No. 110–7994 Installation Instructions Loose Parts Note: Use this chart as a checklist to ensure that all parts have been received. Without these parts, total setup cannot be completed. Description Qty. Proximity switch 2 Block spacer 2 Switch plate 1 Screw, #10 x 1–1/2 inch 2 Screw, #10 x 1–3/4 inch 2 Flat washer, .216 x .
PAGE 2
Installation 1. Place the sweeper on a level surface and apply the tow vehicle parking brake. Make sure the sweeper is in the operating (lowered) position. 2. Unplug the control box wire harness from the sweeper harness (Fig. 1). Do not unplug the power harness from the sweeper. 5 1 2 1 6 4 2 3 3 Figure 2 1. Proximity switch 2. Spacer block 3. Frame mounting bracket 4. Cam spacer 5. Switch cam 6. Mounting pin spacer Figure 1 1. Control box wire harness 2. Sweeper harness 3. Power harness 7.
PAGE 3
8. Loosely assemble the switch plate assembly, block spacer and another switch to the frame mounting bracket with (2) # 10 x 1–1/2 inch screws, .216 x .500 flat washers and # 10 nuts (Fig. 4). 3 10. Mount the yoke spacer and the .375 x .734 flat washer to the upper hole in the left side of the frame mounting bracket with a 5/16 x 1–1/4 inch screw (Fig. 6). The legs of the torsion spring are to be hooked on the yoke spacer and the post on the switch arm (Fig. 7). 2 2 1 1 Figure 4 1.
PAGE 4
3 12. Loosen the (4) screws securing the cover to the remote control box (Fig. 8). Lift the cover off the box enough to unplug the switches from the internal connectors. 2 3 1 3 4 4 6 5 1 6 2 7 6 Figure 8 1. Cover 2. Remote control box Figure 9 3. Switch (2) 4. Plug 1. 2. 3. 4. 13. Remove the switches and the plug from the cover (Fig. 8). Note the switch location for re–installation in the new cover. Discard the cover. Control box cover Decal Indicator light Clamp 5. Audio alarm 6.
PAGE 5
To audio alarm To indicator light Harness connectors To trailer harness To proximity switch To control box harness Figure 10 28. Using the dimensions shown in figure 11, locate and affix the new decal to the front right corner of the sweeper. 3/8 ” 1 3/8” Figure 11 1.
PAGE 6
PAGE 7
PAGE 8